Aspects SWF213SCT Installation Guide

SWF213
Fluorescent Semiflush Fixture
Models SWF213
Safety Precautions
Read all safety precautions and installation instructions carefully
before installing or servicing this fixture. Failure to comply with
these instructions could result in potentially fatal electric shock
and/or property damage.
It is recommended that all wiring be performed by a qualified
electrician. This fixture must be wired in accordance with all national
and local electrical codes.
Do not handle any energized fixture or attempt to energize any
fixture with wet hands or while standing on a wet or damp surface or
in water.
Make sure that the power source conforms to the requirements of the
fixture. (See labels on fixture). Not for use with dimming circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green) or bare metal
contact (metal conduit) between this fixture and the ground
connection of your main power supply panel. The green ground
screw location is clearly marked on the fixture housing.
This fixture is intended for use as general indoor lighting in dry or
damp locations only.
Assembly Instructions
1.
Preparing for installation
Disconnect electrical power before installing or servicing any part of this fixture.
A. Install canopy mounting screws (2) through center screw holes. Attach
mounting plate (1) to junction box (not provided) in position shown with #8-32 x
1-1/2” screws provided.
B. Pull the wires tight and cut cord allowing for 6 inches of wire for junction box
wiring. Carefully remove outer insulation from cord without damaging lead
wires. Strip lead wires back 3/8 inch for wire nut connections. WARNING:
Inspect modified cord and wires for any damaged insulation.
C. Install four decorative bars (6) to canopy by securing them with short screws and
ball nuts (7) (Note – turning the assembly up-side-down may make threading the
screws easier).
2. Wiring
All wiring must take place inside junction box. Caution: Make sure power
is off at fuse or circuit breaker box. Check power wires for damage or scrapes. If
power supply wires are within three inches of ballast use wire suitable for at least
90C (194F). Note: Most dwellings built before 1985 have supply wire rated to 60C.
Consult a qualified electrician before installing.
A. Feed cord through center hole in mounting plate (2).
B. Securely attach green wire to ground supply wire and ground screw located in
mounting plate.
C. Using wire connectors provided, connect white supply wire to white fixture lead.
Connect black hot supply wire to black fixture lead. Do not mix wires. Pull on
each wire lead to make sure connections are secure. Make sure no bare wires are
exposed outside of wire connectors.
3. Fixture mounting
A. Install fixture threaded end through the canopy central hole and secure it with plate (4) and nut (3).
4. Lamping
A. Install two 13-watt self-ballasted compact fluorescent spiral lamps (8) into socket by inserting pins into holder and twist until it
snaps in place.
CAUTION - RISK OF FIRE, Max. 13-watt type GU-24 (provided), TCP 33113SP or Maxlite MLS13GUWW recommended for
replacements only.
5. Diffuser mounting
A. Install glass diffuser (9) over threaded rod and secure with and plastic plate (10), iron plate (11) and nut (12).
B. Install cap (13) over threaded rod and secure it with the knob (14).
6. Power to the fixture can now be restored
Limited Factory Warranty
American Fluorescent Corporation hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating
conditions for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it
does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.
Page 1 of 1
8060613 R1