World Imports WI8102562 Installation Guide

INSTALLATION INSTRUCTIONS
PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS,
AS YOU MAY NEED THEM AT ALATER DATE.
CAUTION – Turn off the main power at the circuit breaker before installing the
Fixture, in order to prevent possible shock.
Remove the fixture and the mounting package from the box and make sure
That no parts are missing by referencing the illustrations on the installation
Instructions.
FOR CEILING MOUNT ( Fig. 4& 5 )
1. A)Place the #8-32 HEX NUT(3) onto the #8-32 FXTURE MOUNTING
SCREW(4). And attach the FIXTURE MOUNTING SCREW to the MOUNTING
RACKET(2).or universal mounting plate (whichever is provided). Do not tighten the
HEX NUTS at this time.(Fig.4)
B) If the fixture uses a single 1/8”IPS NIPPLE(4) for mounting, thread the 1/8”IPS
HEX NUT(3) onto the NIPPLE, and screw the NIPPLE into the MOUNTING
BRACKET(2).without tightening the HEX NUT(3).(Fig.5)
2. Pull the power supply wires out from the OUTLET BOX (1) and mount the
MOUNTING BRACKET (2) or the universal mounting plate to the OUTLET BOX(1),
using MOUNTING SCREWS(10).
1.OUTLET BOX
2.MOUNTING BRACKET
3.#8/32 HEX NUT
4.FIXTURE MOUNTING
SCREW
5.WHITE TO WHITE
WIRE CONNECTION
6.BLACK TO BLACK
WIRE CONNECTION
7.SUPPLY GROUND
WIRE
8.FIXTURE GROUND
WIRE
9.WIRE NUT
10.MOUNTING SCREW
11.CANOPY
12.DECORATIVE NUT
Fig.4
3. Attach the power supply wire to the fixture lead wire by connecting BLACK to
BLACK(6),and WHITE to WHITE(5). Connect the FIXTURE GROUND WIRE (8) to
the SUPPLY GROUND WIRE(7) using a WIRE NUT(9)(not included).
4. Place the CANOPY(11) on the fixture over the OUTLET BOX(1) and onto the
fixture mounting screws﹝ or NIPPLE ﹞,and adjust the #8-32 fixture mounting
screws (or NIPPLE) until they protrude out from the CANOPY(11) 1/4”. Remove the
CANOPY(11) and secure the position of the fixture mounting screw ( or NIPPLE) by
tightening the HEX NUT(S)(3) against the MOUNTING BRACKET(2). Place the
CANOPY(11) back onto the fixture mounting screws,(or NIPPLE), and secure into
place using the DECORATIVE NUT(12) provided.
5. Screw in light bulbs that do not exceed the maximum wattage specified on the
fixture’s wattage rating label, into the socket(s) on the fixture.
INSTALLATION COMPLETED
FOR CHAIN-SUSPENDED CEILING MOUNT(Fig.6)
1. Take the parts out of the mounting package and thread a 1/8” IPS HEX NUT (5)
several turns onto each end of the NIPPLE (4). Screw the end of the NIPPLE (4)
several turns into the threaded hole of the MOUNTING BRACKET (2) but do not
tighten the HEX NUTS (5). Pull the SUPPLY WIRES (9 & 11) and the GROUND
WIRE (8) out from the OUTLET BOX (1) and attach the MOUNTING BRACKET
(2) assembly to the OUTLET BOX (1) using the slotted holes on the MOUNTING
BRACKET (2) and the MOUNTING SCREWS (3) provided.
1.OUTLET BOX
2.MOUNTING BRACKET
3.1/8” IPS HEX NUT
4.NIPPLE
5.WHITE TO WHITE
WIRE CONNECTION
6.BLACK TO BLACK
WIRE CONNECTION
7.SUPPLY GROUND WIRE
8. FIXTURE GROUND
WIRE
9. WIRE NUT
10.MOUNTING SCREW
11.CANOPY
12. .DECORATIVE NUT
Fig.5
1.
2.
3.
4.
5.
6.
7.
Fig.6
2. Thread the SCREW COLLAR LOOP (6) onto the end of the NIPPLE (4) that is
facing down. Place the CANOPY (15) over the OUTLET BOX (1) and adjust the
SCREW COLLAR LOOP (6) and NIPPLE (4) until the midpoint of the outside
threads on the SCREW COLLAR LOOP (6) is centered (aligned) with the surface of
the CANOPY (15). Remove the CANOPY (15) and tighten the HEX NUTS (5)
down on the MOUNTING BRACKET (2) and the SCREW COLLAR LOOP (6).
3. Open up the end links of the CHAIN (17) and attach one end of the CHAIN (17)
onto the FIXTURE LOOP (18) (not shown) of the main section of the fixture. Slide
the THREADED RING (16) and the CANOPY (15) onto the CHAIN (17) (in that
order) and attach the other end of the CHAIN (17) to the SCREW COLLAR LOOP
(6). Close the ends of the chain links.
4. Unravel the fixture’s lead and ground wires and thread the them through every
other link of the CHAIN (17) and out through the SCREW COLLAR LOOP (6) and
NIPPLE (4) assembly, starting with the chain link attached to the FIXTURE LOOP
(18) (not shown) of the main section of the fixture.
5. Attach the power supply wires to the fixture lead wires by connecting the BLACK
SUPPLY WIRE (9) to the SMOOTH FIXTURE LEAD WIRE (or with printing on
the wire)(10) and the WHITE SUPPLY WIRE (11) to the RIBBED FIXTURE
LEAD WIRE (12). Loop the FIXTURE GROUND WIRE (7) around the GROUND
SCREW (14) of the MOUNTING BRACKET (2). (Note: Be sure to leave an extra
3” length of the FIXTURE GROUND WIRE (7) for connection to the SUPPLY
GROUND WIRE (8)). Tighten the GROUND SCREW (14). Connect the remaining
FIXTURE GROUND WIRE (7) to the SUPPLY GROUND WIRE (8) using a WIRE
CONNECTOR (13) (not included).Place wiring and connections inside the OUTLET
BOX (1). (See Fig. 1)
6. Slide the CANOPY (15) and the THREADED RING (16) up the CHAIN (17).
Place the CANOPY (15) over the OUTLET BOX (1) and secure in place by
screwing the THREADED RING (16) onto the SCREW COLLAR LOOP (6).
7. Screw light bulbs into the lamp socket. Note: Make sure they do not exceed the
maximum wattage specified on the fixture’s wattage rating label.
INSTALLATION IS NOW COMPLETED
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
OUTLET BOX
MOUNTING BRACKET
MOUNTING SCREW
NIPPLE
1/8” IPS HEX NUT
SCREW COLLAR LOOP
FIXTURE GROUND
WIRE
GROUND WIRE
BLACK SUPPLY WIRE
SMOOTH FIXTURE
LEAD WIRE
WHITE SUPPLY WIRE
RIBBED FIXTURE
LEAD WIRE
WIRE CONNECTOR
GROUND SCREW
CANOPY
THREADED RING
CHAIN