Sea Gull Lighting 49853BLE-05 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
BEFORE YOU BEGIN
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don't need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
GREEN
GROUNDING
SCREW (G)
MOUNTING
SCREWS (F)
CAP NUTS (E)
*GROUND
WIRE
SOCKET
CUP (B)
CANOPY (I)
BACK
PLATE
(D)
FIGURE 1
RETAINING
RING (H)
SHADE (A)
*NOT INCLUDED
Installation And Safety
Instruction
HC-1367 053008
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_________
HC-1367
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Place back plate (D) against wall and mark location for drywall
anchors. Remove back plate (D) and drill appropriate sized holes into
drywall for anchors.
STEP 2:
Pull supply wires through appropriate opening in back plate (D). Place
back plate (D) against wall and secure by installing dry wall screws
into anchors. Install outlet box screws (not supplied) into outlet box
through appropriate openings in back plate (D) if applicable.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according to
the directions below:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the back
plate (D). Wrap the ground wire from the fixture (if supplied) and the
ground wire from the outlet box (bare metal or green insulated wire)
around the green grounding screw (G) on the back plate (D) and
tighten the green grounding screw (G) to secure. If uninsulated wire is
on the back plate (D), connect the ground wire from the fixture (if
supplied) and the outlet box to it using a small wire connector (not
supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 1:
Make sure no bare wires can be seen outside wire connectors. After
wires are connected, tuck them carefully inside outlet box. Push the
canopy (I) over the mounting screws (F) and against the wall. Secure
canopy (I) in place by threading cap nuts (E) onto mounting screws
(F).
STEP 2:
Place shade (A) on socket cup (B) and secure by threading retaining
ring (H) onto socket (K).
STEP 3:
Hold lamp (J) by base and install to socket (K) by twisting gently.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
FIXTURES WITH A
ONE PIECE LAMP /
BALLAST
COMBINATION
ONE PIECE
LAMP/ BALLAST
COMBINATION (J)
SOCKET (K)
FIGURE 3