Sea Gull Lighting 5233-02 Installation Guide

Installation And Safety Instructions
HC-192
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER SET AT OFF.
GENERAL
You don't need special tools to install this fixture. Be sure to follow
the steps in the order given. Under no circumstances should a
fixture be hung on house electrical wires, nor should a swag type
fixture be installed on a ceiling which contains a radiant type heating
system. Read instructions carefully. If you are unclear as to how
to proceed, consult a qualified electrician.
*OUTLET BOX
*GROUND WIRE
MOUNTING BAR (A)
*OUTLET BOX SCREWS
NUT (B)
NIPPLE (C)
GROUND WIRE (M)
SCREW COLLAR (E)
CANOPY (G)
SCREW COLLAR RING (F)
CHAIN (H)
NUT (L)
NIPPLE (N)
LOOP (I)
092800
ASSEMBLY
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1, 2, and 3. Be careful not to
misplace any of the screws or parts which are needed to install this
fixture.
STEP 1:
Remove cap nuts (J) from scroll (K) and reverse position of scroll (K)
(see illustration). Secure scroll (K) with cap nuts (J).
STEP 2:
Place nipple (N) on center pipe (P) of fixture, up through center of
scroll assembly.
STEP 3:
Screw nut (L) onto nipple (N), far enough to allow top break (R) to
make full contact with scroll (K) assembly. Thread fixture loop (I)
tightly onto nipple (N).
FIGURE 3
TOP BREAK (R)
SCROLL (K)
LOOP (I)
NUT (L)
NIPPLE (N)
NUT (Z)
COUPLING (O)
GROUNDING AND MOUNTING BAR LOCK UP
*OUTLET BOX
GROUND WIRE
TOP BREAK
ASSEMBLY (R)
*WIRE
CONNECTORS
SCROLL (K)
CAP NUTS (J)
MOUNTING
BAR (A)
CENTER PIPE (P)
CANDLE
COVER (Q)
FIGURE 1
*NOT INCLUDED
GREEN
GROUNDING
SCREW (D)
FIGURE 2
NUT (B)
*OUTLET BOX
SCREWS
NIPPLE (C)
*NOT INCLUDED
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT TO OUTLET BOX
OR SUPPORTING SYSTEM ABLE TO SUPPORT THE
WEIGHT OF THE FIXTURE.
INSTALLATION
HC-192
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are
exposed above nut (B). Thread nipple (C) into mounting bar (A) and
secure with nut (B). Attach screw collar (E) to nipple (C).
STEP 2:
Using 2 pair of pliers, open one link of chain (H) and connect it to the
fixture loop (I) at the top of the fixture.
STEP 3:
Slide the screw collar ring (F) and canopy (G), in that order, over
chain (H). Open one link on the other end of the chain (H) and
attach it to the screw collar (E) which has been mounted to the
ceiling nipple (C). BE SURE TO CLOSE ALL CHAIN LINKS
COMPLETELY.
STEP 4:
Lace wires up through chain (H) and pass wires through holes in
screw collar (E). We recommend lacing wire up through every other
link of chain (H).
STEP 5:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
C. Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (M) from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire (M) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NOTE: Underwriters Laboratories does not require all fixtures to
have ground wires. These fixtures still meet all UL specifications.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (G) against ceiling and screw the screw collar
ring (F) to screw collar (E).
STEP 2:
Install candle covers (Q).
STEP 3:
Install lamps.
CLEANING
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
WHITE OR GREY WITH TRACER
WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER
BROWN, GOLD OR BLACK WITH
TRACER
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.