Kenroy Home 90895TS Instructions / Assembly

 WIRE CONNECTOR
(3 PCS)
CROSSBAR
IPPLE
CANOPY
mm SCREW
COLLAR NUT
SCREW
COLLAR LOOP
CHAIN
— —90896С5
(REPLACEMENT
PART)
WRENCH
90792TOOL
UPPER
GLASS SHADE
90895TOPG
(REPLACEMENT PART)
PART)
| бе
oana-—--~ SOCKET
RING
«METAL
RING
GLASS SHADE (A
CHAIN LOOP
DISTRIBUTOR
LASS
SHADE (В)
ARGE
SOCKET
ARM (3 PCS)
GLASS SHADE (C) |
DOB9SBOTES A GLASS SHADE (C)
(REPLACEMENT
PART) INIAL
AVAILABLE PARTS ARE:
90895TOPGS (GLASS SHADE (A))
90896GS (GLASS SHADE (B))
90895B0TGS (GLASS SHADE (C))
SERTE, +
(D.
/STE
3/09
moDeL: 9089S51S
ASSEMBLY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
TOOLS
YOU WILL NEED THE FOLLOWING TOOLS OR EQUIPMENT:
LADDER, SCREWDRIVER, ADJUSTABLE WRENCH, WIRE CUTTERS
AND PLIERS.
UNPACK THE FIXTURE
GLASS SHADE (B)
(REPLACEMENT
YOU SHOULD HAVE RECEIVED THE FOLLOWING PARTS IN THE
PACKAGE: CANOPY, CHAIN, FIXTURE ASSEMBLY, (5) GLASS
SHADES, (3) METAL RINGS, (3) SOCKET RINGS, FINIAL AND
WRENCH. PLACE ALL PARTS ON A SOFT SURFACE.
MOUNTING HARDWARE PACKAGE:
SCREW COLLAR LOOP, SCREW COLLAR NUT, NUT, NIPPLE,
(2) 8-32 X 1-1/4" SCREWS, CROSSBAR, GREEN GROUND
SCREW AND (3) WIRE CONNECTORS.
FIXTURE ASSEMBLY
1. INSTALL A 7 WATT MAX. TYPE "C" BULB (NOT INCLUDED)
INTO UPPER SOCKET.
2. PLACE GLASS SHADE (A) ON TOP OF DISTRIBUTOR AND
SECURE WITH CLIP.
S. DETERMINE THE LENGTH OF CHAIN REQUIRED TO HANG
THE FIXTURE AT THE DESIRED HEIGHT. USING PLIERS, OPEN
ONE END LINK OF CHAIN AND ATTACH TO THE CHAIN LOOP
ON TOP OF THE FIXTURE. REMOVE OR ADD CHAIN AS
DESIRED AT THIS TIME. LACE FIXTURE WIRE AND GROUND
WIRE UP THROUGH EVERY OTHER LINK OF CHAIN.
TO SPREAD A LINK OF CHAIN
USE A PAIR OF PLIERS AND A SCREWDRIVER AS
SHOWN ABOVE, BEING CAREFUL TO WRAP THE
JAWS OF THE PLIERS WITH CLOTH TO PROTECT
THE FINISH OF THE CHAIN.
**xSTOP** COMPLETE INSTALLATION
INSTRUCTIONS ON NEXT PAGE BEFORE
CONTINUING TO FINAL ASSEMBLY.
FINAL ASSEMBLY
1. INSTALL A 7 WATT MAX. TYPE “C” NIGHT LIGHT BULB
(NOT INCLUDED) INTO LOWER SOCKET.
2. SLIDE GLASS SHADE (C) OVER STEM AND SECURE WITH
FINIAL.
3. PLACE A GLASS SHADE (B) OVER EACH LARGE SOCKET,
THEN SECURE WITH A METAL RING AND A SOCKET RING.
(WRENCH INCLUDED)
4, INSTALL A 60 WATT MAX. TYPE "A" BULB (NOT
INCLUDED) INTO EACH LARGE SOCKET.
5. RESTORE POWER. YOUR NEW FIXTURE IS NOW READY TO
USE.
90895TS INSTRUCTIONS
SUPPLY GROUND WIRE = - | OUTLET BOX
< WHITE
BLACK SUPPLY WIRE - SUPPLY WIRE
CEILING Е | WIRE CONNECTORS
BACK OR SMOOTH” —— | (3) REQUIRED
FIXTURE WIRE:
WHITE OR RIBBED
8—32 SCREWS, FIXTURE WIRE
SUPPLIED WITH BOX
All
ROSSBAR
NIPPLE -
IXTURE GROUND WIRE
CANOPY sa
REEN GROUND SCREW
SCREW COLLAR NUT
SCREW COLLAR LOOP
CHAIN
INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
CAUTION
TO AVOID POSSIBLE ELECTRIC SHOCK, MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL. IF YOU
ARE REPLACING AN EXISTING FIXTURE, FIRST TURN THE FIXTURE OFE. NEXT, TURN THE WALL SWITCH OFF.
FINALLY, GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME. TURN THE FUSE OR BREAKER TO THE OFF
POSITION. SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER.
* ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES. IF YOU ARE NOT
FAMILIAR WITH WIRING, YOU SHOULD USE A QUALIFIED ELECTRICIAN.
** THIS FIXTURE IS INTENDED TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE
FIXTURE.
COMPLETE FIXTURE ASSEMBLY INSTRUCTIONS FIRST (SEE PREVIOUS PAGE).
1. ATTACH THE CROSSBAR TO THE CEILING OUTLET BOX USING THE TWO SCREWS PROVIDED WITH THE OUTLET
BOX. (NOTE: IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT, USE THE (2) 8-32 x 1-1/4" SCREWS
PROVIDED IN THE MOUNTING HARDWARE PACKAGE). NEXT, SCREW THE SCREW COLLAR LOOP ONTO THE NIPPLE
AND THEN SCREW THE NIPPLE INTO THE CROSSBAR.
2. SLIDE THE SCREW COLLAR NUT AND THEN THE CANOPY ONTO THE END OF THE CHAIN. THEN FASTEN THE
END LINK OF CHAIN TO THE SCREW COLLAR LOOP.
3. INSERT THE FIXTURE WIRE AND THE GROUND WIRE UP THROUGH THE NIPPLE. CONNECT THE WHITE OR
RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST—ON WIRE
CONNECTORS PROVIDED. CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE
SAME MANNER. INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE CROSSBAR
THEN CONNECT THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE
TWIST—ON WIRE CONNECTOR PROVIDED.
4. TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX. SPREAD THE ELECTRICAL SPLICES SO THAT THE
BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE. NEXT
RAISE THE CANOPY TO THE CEILING AND SECURE IN PLACE BY SCREWING THE SCREW COLLAR NUT ONTO THE
SCREW COLLAR LOOP.
ENTE,
5. SEE PREVIOUS PAGE FOR FINAL ASSEMBLY INSTRUCTIONS. e
с US
/S TED
3/09 90895TS INSTALLATION