AireRyder LK51211OR Use and Care Manual

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
LK51211
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless
additional support is provided for the fan.
Fig.1
Motor
Black or Blue Wire
Switch Box
Wire Nut
Black Wire
Washer
Center Plug
Fig.2
White Wire
White Wire
Hex Nut
Motor
Screw
Black or Blue Wire
Wire Nut
Black Wire
Screw
Switch Box Cover
Nipple
Switch Box Cover
White Wire
Terminal (Groove)
Terminal (Tongue)
White Wire
Switch Box
Nipple
Set Screw
(6 x 32 20mmL)
Light Kit
Fig.3
Motor
Glass Shade
Set Screw
Light Kit
Clip
Fig.4
For Light Kit:
Metal Frame
Short Nipple
Pull Chain
E26 medium base spiral
fluorescent Bulb
(Max.13W, incluced)
Glass Shade Assembly
1. Place the glass shade into the metal frame
as shown in Fig.4, secure it with clips and
set screws.
2. Remove the switch box cover from the switch
box of the fan by loosing the three switch box
Rubber Pad
Metal Pad
screws.
Hex Nut
3. Unscrew the center plug from the switch box
Cover
cover and discard it. (Fig.1)
Finial
4. Thread the fixture wire through the switch box
cover. (Fig.1)
5. For fan style that is shown in Fig.1: Attach the nipple of the light kit to the hole of the switch box
cover, then thread the wires through the washer and hex nut, then secure them tightly.
6. For fan style that is shown in Fig.2: Thread the fixture wire through the switch box, then attach the
light kit to the switch box and secure it with two set screws (6x32 20mmL).
7. Pull out the wires from the switch box. Make wire connections using the wire nuts:
---The black wire from light kit to the black or blue wire from the fan.
---The white wire from light kit to the white wire from the fan.
---Carefully put wires back into the switch box.
8. Attach the switch box cover back to the switch box using the three switch box screws.
9. Install bulbs (included). See relamping label at socket area or packaging for maximum allowed
wattage.
10. Slip the glass shade assembly up through the pull chain and the short nipple, secure them with
a rubber pad, metal pad and hex nut.
11. Slip the cover up through the pull chain and the short nipple, secure it with finial.
12. Turn on the power at the main fuse or circuit breaker box.
(You can control the light with the pull chain)
LK51211 --- Page 1
F
A
N
C
090406
O
For Semi-Flush
1. Take out the parts from the hardware package For
Semi-Flush.
2. Attach two screws to the mounting strap, and secure
it with two lock nuts. Adjust the length of the screws
if necessary.
3. Attach the mounting strap to the outlet box by using
two mounting screws.
4. Thread the fixture wires through the coupling, hex nut,
long nipple, big tube, cap, canopy, metal pad, washer,
grounding pad and another hex nut.
5. Secure the coupling onto the stem on the top of the
light kit. Then screw the long nipple into the coupling,
then secure it with a hex nut.
6. Slip the big tube, cap with the open side facing downward
and the canopy down through the long nipple, secure them
together with a metal pad, washer, grounding pad and hex
nut.
7. Follow step 1 as For Light Kit.
8. Cut the redundant wires if necessary. Pull out the outlet wires
and the house grounding wire from the outlet box. Make wire
connections using the wire nuts:
---Connect the black wire from fixture to the black wire from
power source.
---Connect the white wire from fixture to the white wire from
power source.
---Attach the fixture grounding wire to the mounting strap with
the green grounding screw. Then connect it to the house
grounding wire with the wire nut.
Carefully put wires back into the outlet box.
9. Attach the canopy to the mounting strap,
and secure it with the bolt nuts.
10. Follow steps 9~12 as For Light Kit.
Outlet Box
House Grounding Wire
Wire Nut
Screw
Mounting Strap
Lock Nut
Mounting Screw
Green Grounding Screw
Hex Nut
Grounding Pad
Washer
Metal Pad
Canopy
Bolt Nut
Cap
Big Tube
Long Nipple
Hex Nut
Coupling
Stem
E26 medium base spiral
fluorescent Bulb
(Max.13W, incluced)
Short Nipple
Pull Chain
Glass Shade Assembly
Rubber Pad
Metal Pad
LK51211 --- Page 2
F
A
N
C
090406
O