Hunter 99140 Instructions / Assembly

Traditional
3-Light Fitter
TYPE-A ASSEMBLY
Models 99134, 99135, 99136,
99138, 99140
Compatible with:
2xxxx Types A - Z
51000-58999 fan series
59500-59999 fan series
Select Casablanca Fans
er
ow
P
rn
Tu
Read entire installation instructions
carefully before beginning installation
and save these instructions.
OFF
OR
Cap
Screw
Switch
Housing
Cap
If your fan’s switch housing cap
resembles this one, remove the
cap screws with a Phillips head
screwdriver. Then follow the
instructions for TYPE-A ASSEMBLY.
OR
Switch
Housing
Screw
Switch
Housing
Assembly
Screw
Plug
Button
If your fan’s switch housing cap
resembles this one, remove the
whole switch housing by removing
the switch housing screws with a
Phillips head screwdriver. Remove
the plug button. Then follow the
TYPE-B ASSEMBLY INSTRUCTIONS.
Switch
Housing
Cap
If your fan’s switch housing cap
resembles this one, remove the whole
switch housing by removing the switch
housing screws with a Phillips head
screwdriver. Remove the two cap screws
from the inside of the switch housing.
Reinstall the switch housing. Tighten
the switch housing screws. Then follow
the instructions for TYPE-A ASSEMBLY.
GO TO
NEXT PAGE
Switch
Housing
Wire
Connector
If your fan does not have pin connectors on the
wires coming from the switch housing, install
the wiring harness provided. Using the provided
wire connectors connect the white wire from
the fan to the white wire from the wire harness
and connect the black or blue wire from the fan
to the black wire from the wire harness.
TYPE-B ASSEMBLY
START
HERE
WHICH ASSEMBLY
METHOD WILL I USE?
1.888.830.1326
Using the single pin connectors, connect the
black or blue wire from the fan to the black
wire from the light kit. Connect the white
wire from the fan to the white wire from the
light kit.
Note: Do not allow the light kit to hang only
by the wire connectors.
Lift the light kit up to meet the lower switch
housing. Guide the two pre-installed light
kit screws into the holes in the lower switch
housing. Tighten screws.
Light Kit
Screw
GO TO
NEXT PAGE
Switch
Housing
Switch Housing
Assembly Screw
Wire
Connector
If your fan does not have pin connectors on the
wires coming from the switch housing, install
the wiring harness provided. Using the provided
wire connectors connect the white wire from
the fan to the white wire from the wire harness
and connect the black or blue wire from the fan
to the black wire from the wire harness.
Feed the light kit wires through the center hole
in the switch housing. Then attach the switch
housing to the light kit by installing the light kit
screws into the bottom of the switch housing.
Using the single pin connectors, connect the
black or blue wire from the fan to the black
wire from the light kit. Connect the white
wire from the fan to the white wire from the
light kit.
Note: Do not allow the light kit to hang only
by the wire connectors.
MA015-01 • 12/31/13
Lift the light kit up to meet the upper
switch housing. Install the switch housing
assembly screws. Tighten screws.
Improper installation could cause the light fixture to
fall, or result in electrical shock or personal injury.
FOR BOTH ASSEMBLIES
1.888.830.1326
Thumb Screw
Shade
(not included)
er
ow
P
rn
Tu
Installing the shades - To install the
shade, first loosen the thumb screws.
Raise the shade to the light fixture.
Tighten all thumbscrews securely.
Installing the bulb - Install a bulb into each
socket. When necessary, replace bulbs with
bulbs of same type and wattage.
Installing the pull chain pendant Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit.
TROUBLESHOOTING
ONE YEAR WARRANTY
This product is warranted to the original purchaser by Casablanca
Fan Company/Hunter Fan Company against defects in material and
workmanship for one (1) year from date of purchase. During the
warranty period, we will repair or, at our option, replace a defective
product at no charge. For information on how to obtain service,
contact the Casablanca/Hunter Service Department by calling our
toll-free number at 888-830-1326. Damage to the product caused
by mishandling, improper installation or modification is not covered
by this warranty. This warranty is given in lieu of all other warranties
expressed or implied. Some states do not allow limitations of time
on an implied warranty, therefore the above limitations may not
apply in every case. This warranty states specific legal rights which
may vary from state to state.
Lights don’t come on.
• Make sure that the bulbs are properly installed.
ON
Pull Chain
Pendant
To turn lights on and off, pull the pull
chain pendant coming from the center
of the light kit.
READ AND SAVE THESE INSTRUCTIONS
This product conforms to UL Standard 507.
WARNINGS
• Make sure power switch is on.
• Pull the pull chain to make sure it is on.
• Check the circuit breaker to ensure the power is turned on.
• Check the pin connections in the light kit.
• Refer to the fan manual for locating the fan’s wiring. Verify that the
light and power wires are correctly connected to the ceiling and
the light kit.
w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan
directly from building structure and/or an outlet box marked acceptable for
fan support of 70 lbs. (31.8 kg) and use the mounting screws provided with the
outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your fan,
disconnect the power by turning off the circuit breakers to the outlet box and
associated wall switch location. If you cannot lock the circuit breakers in the
off position, securely fasten a prominent warning device, such as a tag, to the
service panel.
CAUTIONS
If you have problems installing or operating your light kit, do not return
this product to the dealer. Call our Consumer Affairs Hotline.
888-830-1326
MA015-01 • 12/31/13
c.1 - All wiring must be in accordance with national and local electrical codes ANSI/
NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.