Yosemite Home Decor LK919-ORB Instructions / Assembly

Owner’s Manual
QUEENIE2
UL
R
WARNING : Read and follow these instructions carefully and be cautious of all warnings shown throughout.
READ AND SAVE THESE INSTRUCTIONS
Warning: To avoid the risks of fire, electrical shock or injury,
please observe the following:
1.
To ensure the correct and complete installation, be sure to read the instructions and review the diagrams
carefully and thoroughly before beginning installation.
2.
If possible, mount the ceiling fan on a ceiling joist. The joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4" x 2-1/8" deep METAL octagon box is
required; one UL listed as "suitable for fan support ". The box and its supporting members must not be able
to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should be
performed by qualified personnel.
3.
Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in
the carton until ready to be installed to protect its finish. If you are installing more than one ceiling fan, make
sure that you do not mix fan blade sets.
4.
Make sure that your installation site will not allow rotating fan blades to come in contact with any object.
Blades should be at least 7 feet from the floor when fan is in operation.
5.
To avoid any possible accidents such as electric shock, be sure ceiling fan is not connected to power source
before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or
the National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can check the
strength of the supportive ceiling members and make the proper installations and connections.
6.
See wire connection instruction for your guide. Electrical diagrams are for reference only. Read the
instructions carefully and connect wires correctly and completely.
7.
After making electrical connections, spliced conductors should be turned upward and pushed carefully up
into the outlet box. The wires should be spread apart from the grounded conductor. Ground conductor
should be placed opposite to the outlet box from the "HOT" wires.
8.
After fan is completely installed, double check everything to make sure that all connections are secure to
prevent fan from falling and/or causing damage or injury.
9.
The fan can be used immediately after installation. The bearings are adequately charged with grease so
that, under normal condition, further lubrication should not be necessary.
Important Notes:
1.
2.
3.
The fan must be turned off and at a complete stop before reversing fan direction.
Light kits that are not packed with the fan must be UL or CUL listed and should be installed per light kit's
installation instructions.
This fan is suitable for indoor locations only.
P1
I - Opening of the box
1.Unpack and inspect the fan carefully to be certain that all contents are
included. Identify and check the parts referred to the drawing below.
Remote Control
Transmitter
Mounting Bracket
Suitable for use with solid - state speed control
Canopy
Glass Shade Assembly
Screw
2pcs
Wire nuts
7pcs
Hardware Bag
Downrod
Spring Washer
3pcs
Lock Washer
3pcs
Wood Screw
3pcs
Tooth Washer
3pcs
Wire Nuts (For 120V Only)
4pcs
Blade Balance Kits
1pcs
Fan Assembly
Yoke cover
Blade Holder
Bulb
Blade
Switch Housing
Blade Screw
16pcs
Paper Washer
16pcs
Motor Screw
11pcs
Leaf Spring
3pcs
Screw
3pcs
Outlet Box
Mounting
Bracket
OFF OFF OFF
4.
2.
3.
Turn off power at the breaker
box to avoid possible
electrical shock.
Use a metal outlet box suitable for
fan support.
Be sure that the box can support
a minimum weight of 40 pounds.
Secure the outlet box directly to the
building structure using wood
screws (provided).
P2
Install the mounting bracket
to outlet box in the ceiling
using the washers and the
mounting screws provided
in the hardware bag.
Do not use existing
mounting bracket
in the outlet box.
5. Yoke & Downrod Assembly
Cotter Pin
Wires
Canopy
Canopy
Downrod
Yoke cover
Cross Pin
Downrod Set Screw
Downrod
Yoke Cover
Cross Pin
Yoke
Cotter Pin
Yoke
Downrod Set Screw
(3)
Then insert the cross pin again through yoke &
downrod and secure with cotter pin.
(4)
Tighten both downrod set screws to further secure
downrod, then pull down the yoke cover to cover yoke.
(1)
Feed motor lead wires through yoke cover,
canopy and downrod.
(2)
Take off the cotter pin and cross pin in order
to insert downrod into yoke.
5a.Up Glass Shade Assembly
Glass Screws(3)
Up Glass Shade
Spring Clip(3)
Grill
Place the up glass shade onto
grill & secure the glass shade
with three glass screws / spring
clips from hardware bag on grill.
Light Bulb(4)
Gently install Light bulbs on lampholders.
6. Hanging the fan
Mounting
Bracket
Mounting
Bracket
Ball Notch
(2)
Rotate fan so that the ball notch engages the
ridge in the mounting bracket.
(1)
Carefully lift fan assembly onto
mounting bracket.
6-2.
IMPORTANT: THE WOOD SCREW AND ITS SUPPORT MUST
BE ABLE TO FULLY SUPPORT THE WEIGHT OF AT LEAST 100 LBS.
To ensure safely install the secondary support as follows:
(1). Using the wood screw and flat washer provided.
Pass through close loop of safety cable to wood screw.
(2). Secure the wood screw to ceiling joist and make sure
the safety cable has been tightened securely.
Safety cable
P3
II - Remote Control
1.Prepare the parts of the remote control.
Receiver
Code Switches
2
3
4
4
1 2 3
1
Transmitter
Code Switches
2. Setting the code on the transmitter.
2-1. Remove the battery cover of the remote control.
2-2. Slide code switches to your choice for an ON and OFF position. Use a small screwdriver to slide each
of the switches.
2-3. Install a 9V DC battery ( included).
2-4. Install battery covers on transmitter.
3. Setting the code on the receiver:
3-1. Slide the code switches to the receiver. Be sure that the code is similar to the code set at the
transmitter.
4. For remote control wiring connection to the fan:
4-1. Follow the diagram below and be sure that exposed wires are secured inside wire nuts or the
terminal block.
Note: Wires from the house may vary in color and may not include ground wire (green).
4-2. When the wiring is completed, gently push wires into the junction box with wire nuts pointing upward.
From House
From Remote
White
White
(AC-N)
Bla
From Fan
White
ck
Blac
k
Bl
ue
Black
O
(AC-L)
ra
White
( Motor - N )
( Motor - L )
ng
e
( for light kit )
( for up light kit )
Green
Black
Blue
Orange
Green
( from downrod )
( for ground wire )
Green
Secure with twist - lock wire nuts (Included).
( from mounting bracket )
III.Canopy Installation
(1) Push up the canopy until the two canopy
screws on mounting bracket are engaged
with key holes in canopy.
Canopy
(2) Rotate the canopy slightly until the two
canopy screw heads are in the small end
of the key holes.
Canopy
Screw
(3) Tighten both canopy screws.
P4
Key Hole
IV. Blade Installation
Blade Screw
Paper Washer
1.
Attach blade to blade holder
with paper washer & blade screws
provided from hardware bag.
Make sure that all screws are
firmly tightened.
Blade
Blade Holder
2.Blade Assembly To Motor
Remove 3pcs of motor stoppers .
Motor Stopper
Attach the blade assembly to motor firmly
using motor screws from hardware bag .
NOTE: Do not bend blade or blade arm to
prevent wobble.
Motor Screw
Blade Assembly
V. Switch Housing Assembly
If you don’t need to attach with light kit, just attach switch housing
to switch housing cover with three screws existing on switch housing cover.
Be sure to connect 9 pin terminals first before you proceed above step.
Switch Housing
Cover
Blue Wire
Screw
White Wire
9 pin terminals from fan
Black Wire
Switch Housing
Center Nut
(*You may need to remove center nut for light kit installation.)
TURN ON THE POWER. INSTALLATION IS SUCCESSFUL
AND THE FAN IS READY FOR OPERATION.
P5
LIGHT KIT INSTALLATION INSTRUCTIONS
Parts Bag
Wire Nut
2pc.
Pull Chain Knob
1ps
1. Fan and Light Kit Assembly
Take switch housing off by loosening three screws
attached to it if switch housing is attached to fan.
Remove center nut from switch housing and
Insert wires existing from Light Kit Fitter by passing
through center hole and attach Light Kit Fitter to Switch
Housing with threaded tube and/or fasten with spring
washer and hex nut.
Light Kit
Fitter
Screw
Switch Housing.
Cover
2. Make wire connections for light kit
( 1 ). White wire from Light Kit to white wire
from switch housing and connect by wire nut.
( 2 ). Black wire from Light Kit to blue wire
from switch housing and connect by wire nut.
( 3 ). Attach switch housing and light kit assembly
onto switch housing cover and secure by three
screws.
White Wire
White Wire
Spring Washer &
Hex Nut
Blue Wire
Wire Nut
Black Wire
Switch Housing
3. Glass Shade Attachment
(1).
Unscrew Glass Shade Holder
off from Light Kit.
(2).
Attach Glass Shade to Light Kit
and secure with Glass Shade
Holder taken off from Step (1).
P6
(3).
Attach Lamp to Lamp-holder.
(4).
Attach pull chain knob to light kit.
The light kit is ready for operation.