AireRyder LK55512BBZ-C Instructions / Assembly

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
LK38312
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless
additional support is provided for the fan.
Motor
Black or Blue Wire
Wire Nut
Black Wire
Switch Box
White Wire
White Wire
Hex Nut & Washer
Switch Box Screw
Center Plug
Switch Box Cover
Nipple(-a)
Cap
Pan
Socket Set
Nipple(-b)
Glass Shade
Finial
Pull Chain
For Light Kit:
1. Remove the switch box cover from the switch box of the fan by loosing the three switch box screws.
2. Unscrew the center plug from the switch box cover and discard it.
3. Thread the fixture wire through the switch box cover.
4. Attach nipple(-a) of the light kit to the switch box cover, then secure it with a washer and hex nut.
5. Cut the redundant wires if necessary. Pull out the wires from the switch box. Make wire connections
using the wire nuts:
---The black wire from the fixture to the black (or blue) wire from the switch box.
---The white wire from the fixture to the white wire from the switch box.
Carefully tuck the wires back into the switch box.
6. Attach the switch box cover back to the switch box using the three switch box screws.
7. Install bulbs (not included). See relamping label at socket area or packaging for maximum allowed
wattage.
8. Thread the pull chain through the glass shade and the finial. Carefully attach the glass shade to the
pan by inserting nipple(-b), then secure it with the finial.
9. Turn on the power at the main fuse or circuit breaker box. (You can control the light with the pull chain.)
TM
LK38312 --- Page 1
060218
For Ceiling Light: (See Fig.1)
Mounting Parts for Ceiling Light
1. Take out the the coupling, two hex nuts, washer, nipple(-c),
top cap, canopy, washer and grounding pad from the
Outlet Box
hardware package for ceiling light.
House Grounding Wire
2. Secure the coupling to nipple(-d), then screw nipple(-c)
Wire Nut
into the coupling and secure it with a washer and hex nut.
Screw
3. Attach the top cap with the open side facing downward
Mounting Strap
and the canopy with the open side facing upward to the
Lock Nut
Green Grounding Screw
fixure by inserting nipple(-c), then secure them with a
Mounting Screw
washer, grounding pad and hex nut.
Fixture Grounding Wire
4. Attach two screws to the mounting strap, then secure
Hex Nut
Grounding Pad
them with two lock nuts. Adjust the length of the screws
Washer
if necessary.
Canopy
5. Attach the mounting strap to the outlet box by using two
Bolt Nut
Top Cap
mounting screws.
Nipple(-c)
6. Pull out the outlet wires and the house grounding wire
Hex Nut & Washer
Coupling
from the outlet box. Make wire connections using the wire
Nipple(-d)
nuts:
Fixture
---The black wire from fixture to the black wire from the
outlet box.
---The white wire from fixture to the white wire from the
Fig.1
outlet box.
---Attach the fixture grounding wire to the mounting strap
with the green grounding screw. Then connect it to the house grounding wire with a wire nut.
Carefully tuck the wires back into the outlet box.
7. Attach the canopy to the mounting strap by inserting two screws, then secure them with the bolt nuts.
8. Follow steps 7~9 as for Light Kit.
TM
LK38312--- Page 2
060218