none 13431103002300 Use and Care Manual

Item #000-000
Model #SW1478 ORB
USE AND CARE GUIDE
DURANGO 52 INCH CEILING FAN
Questions, problems, missing parts? Before returning to the store,
call Home Decorators Collection Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
1-877-527-0313
HOMEDEPOT.COM/HOMEDECORATORS
THANK YOU
Table of Contents
Operation .....................................................................15
Remote Control Operating Instructions...........................15
Reverse Function Button Operating Instructions ..............15
Installing the Remote Control Holder .............................16
Table of Contents ..........................................................2
Safety Information .........................................................2
Warranty .........................................................................3
Care and Cleaning.......................................................16
Pre-installation .............................................................. 3
Specifications .......................................................................... 3
Tools Required ......................................................................... 3
Hardware Included .................................................................. 4
Package Contents ................................................................... 5
Troubleshooting ..........................................................17
Service Parts................................................................18
Installation ..................................................................... 6
Assembly ....................................................................... 7
Hanging the Fan ...................................................................... 7
Attaching the Fan Blades ...................................................... 12
Installing the Light Kit ........................................................... 13
Safety Information
□
Read and save these instructions.
□
To reduce the risk of electric shock, ensure electricity has
been turned off at the circuit breaker or fuse box before
beginning.
□
All wiring must be in accordance with the National Electrical
Code “ANSI/NFPA 70-1999” and local electrical codes.
Electrical installation should be performed by a qualified
licensed electrician.
□
The outlet box and support structure must be securely
mounted and capable of reliably supporting a minimum of 35
lbs. Use only UL Listed outlet boxes marked “FOR FAN
SUPPORT.”
□
The fan must be mounted with a minimum of 7 ft. clearance
from the trailing edge of the blades to the floor.
□
To avoid personal injury or damage to the fan and other
items, be cautious when working around or cleaning the fan.
□
Do not use water or detergents when cleaning the fan or fan
blades. A dry dust cloth or lightly dampened cloth will be
suitable for most cleaning.
□
After making electrical connections, spliced conductors
should be turned upward and pushed carefully up into the
outlet box. The wires should be spread apart with the
grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on
the other side of the outlet box.
□
All setscrews must be checked and retightened where
necessary before installation.
WARNING: To reduce the risk of electrical shock or fire, do
not use this fan with any solid-state fan speed control device.
It will permanently damage the electronic circuitry.
WARNING: To reduce the risk of personal injury, do not
bend the blade arms (also referred to as flanges), when
installing the brackets, balancing the blades, or cleaning the
fan.
WARNING: Do not insert foreign objects between rotating
fan blades.
WARNING: To reduce the risk of fire, electric shock, or
personal injury, mount the fan to the outlet box marked
acceptable for fan support with the screws provided with the
outlet box.
CAUTION: To reduce the risk of personal injury, use only
the screws provided with the outlet box.
2
Warranty
We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period
of 15 years after the date of purchase by the original purchaser. We also warrant that all other fan parts, excluding any glass or acrylic
blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the
date of purchase by the original purchaser. We agree to correct such defects without charge or at our option replace with a comparable or
superior model if the product is returned. To obtain warranty service, you must present a copy of the receipt as proof of purchase. All
costs of removing and reinstalling the product are your responsibility. Damage to any part such as by accident, misuse, improper installation or by affixing any accessories, is not covered by this warranty. Because of varying climatic conditions this warranty does not cover
any changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling. Brass finishes of this type give their longest useful
life when protected from varying weather conditions. A certain amount of “wobble” is normal and should not be considered a defect.
Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. We hereby disclaim
any and all warranties, including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by
law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty.
Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The retailer shall
not be liable for incidental, consequential, or special damages arising out of or in connection with product use or performance except as
may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above
exclusion or limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from
state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty
must be paid by the customer.
Contact the Customer Service Team at 1-877-527-0313 or visit www.HOMEDEPOT.COM/HOMEDECORATORS
Pre-Installation
SPECIFICATIONS
Fan size
Speed
Volts
Amps
0.25
Watts
15.3
RPM
68
CFM
1959
120
0.38
32.8
108
3365
0.50
59.4
160
5230
Low
52 in.
Medium
High
N.W.
G.W.
8.82 kg
10.10 kg
(19.40 lb)
(22.22 lb)
C.F.
1.85 ft.
®
NOTE: These are approximate measures. They do not
include amps and wattage used by the light kit.
TOOLS REQUIRED
Phillips
screwdriver
Flat blade
screwdriver
Step
ladder
3
Wire
stripper
Electrical
Tape
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-877-527-0313 for further assistance.
Pre-Installation (continued)
HARDWARE INCLUDED
NOTE: Hardware shown to actual size unless noted
otherwise in the table below.
AA
EE
JJ
FF
KK
GG
LL
HH
MM
II
NN
BB
CC
DD
Part
Description
Quantity
AA
Blade screw
16
BB
Fiber washer (not to scale)
16
CC
Blade holder screw
11
DD
Balance kit (not to scale)
1
EE
Remote control holder mounting screws
2
FF
Wire nuts
6
GG
HH
Cross pin (not to scale) (preassembled)
Hitch pin (preassembled)
1
1
II
Lock pin (not to scale) (preassembled)
1
JJ
Hanger ball set screw (preassembled)
1
KK
Fan motor assembly coupling set screw (preassembled)
2
LL
Mounting bracket screw (preassembled)
2
MM
Fan motor assembly mounting ring screw (preassembled)
3
NN
Light kit plate screw (preassembled)
3
4
Pre-Installation (continued)
PACKAGE CONTENTS
G
M
H
I
A
N
B
J
C
O
D
K
E
P
F
Part
Description
L
Quantity
5
Part
I
Description
Blade holder
Quantity
5
A
Blade
B
Mounting bracket
1
J
Light kit plate
1
C
Canopy
1
K
17W LED asembly
1
D
E
Canopy cover
Hanger ball (preassembled)
1
1
L
M
Glass shade
Receiver
1
1
F
Downrod (preassembled)
1
N
Remote control
1
G
Couping cover
1
O
Remote control holder
1
H
Fan motor assembly
1
P
12V Battery
1
5
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-877-527-0313 for further assistance.
Installation
MOUNTING OPTIONS
WARNING: To reduce the risk of fire, electric shock, or
personal injury, mount the fan to an outlet box marked
acceptable for fan support using the screws provided with the
outlet box. An outlet box commonly used for the support of
lighting fixtures may not be acceptable for fan support and
may need to be replaced. If in doubt, consult a qualified
electrician.
1
If your ceiling fan does not have an existing UL-listed mounting
box, then install one using the following instructions:
□
Disconnect the power by removing the fuses or turning off
the circuit breakers.
□
Secure the outlet box (1) (not included) directly to the
building structure. Use appropriate fasteners and materials
(not included). The outlet box and its bracing must be able
to fully support the weight of the moving fan (at least 35
lbs.). Do not use a plastic outlet box.
□
The illustrations to the right show three different ways to
mount the outlet box (not included).
□
To hang your fan where there is an existing fixture but no
ceiling joist, you may need an installation hanger bar (3) (not
included), as shown.
1
NOTE: You may need a longer downrod to maintain proper
blade clearance when installing on a steep, sloped ceiling.
The maximum angle allowable is 18°. If the canopy touches
the downrod, remove the decorative canopy bottom cover
and turn the canopy 180° before attaching the canopy to the
mounting plate (2).
2
3
1
6
Assembly — Hanging the Fan
1
2
Attaching the mounting bracket to
the electrical box
WARNING: To reduce the risk of fire, electric shock, or
other personal injury, mount the fan only to an outlet box or
supporting system marked acceptable for fan support and
use the mounting screws provided with the outlet box.
□
□
Place the slots from mounting bracket (B) over the two
screws provided with the outlet box. Slide the mounting
bracket (B) until it locks in place at the narrow section
of the slots.
Attaching the downrod to the
fan motor assembly
□
Loosen the two set screws (KK) from the fan motor
assembly (H) coupling.
□
Remove the hitch pin (HH) and lock pin (II) from the
downrod (F). Remove the hanger ball (E) from the
downrod (F) by loosening the hanger ball set screw (JJ),
and removing the cross pin (GG), then sliding the hanger
ball (E) off of the downrod (F).
□
Carefully feed the fan wires up through the downrod (F).
Thread the downrod (F) into the fan motor assembly (H)
coupling. Line up the holes and replace the lock pin (II)
and the hitch pin (HH). Tighten the set screws (KK).
Securely tighten the two mounting screws.
GG
E
B
JJ
F
HH
II
KK
H
B
7
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-877-527-0313 for furtherBassistance.
Assembly — Hanging the Fan (continued)
3
4
Attaching the coupling cover, canopy
cover, and canopy to the downrod
□
□
Slip the coupling cover (G), canopy cover (D), and canopy
(C) onto the downrod (F). Carefully reinstall the hanger
ball (E) onto the downrod (F), and ensure that the cross pin
(GG) is in the correct position, the set screws (JJ) are tight,
and the wires are not twisted.
GG
Hanging the fan motor assembly
from the mounting bracket
Lift the fan motor assembly (H) into position, and place the
hanger ball (E) into the mounting bracket (B). Rotate the
fan motor assembly (H) until the check groove drops into
the registration slot (OO) and seats firmly. The downrod (F)
should not rotate if this is done correctly.
JJ
E
B
C
E
F
OO
D
F
G
H
8
Assembly — Hanging the Fan (continued)
5
Preparing the receiver and remote control
WARNING: To avoid possible electrical shock, ensure the
electricity is turned off at the main fuse box before wiring.
CAUTION: Do not use with a wall light dimmer switch.
NOTE: If you feel you do not have enough electrical
wiring knowledge or experience, have your fan installed
by a licensed electrician.
M
N
This remote control unit is equipped with 16 code
combinations to prevent possible interference from or to
other remote units. The frequency switches on your
receiver (M) and remote control (N) have been preset at
the factory. Please recheck to make sure the switches on
the remote control (N) and the receiver (M) are set to the
same position. Any combination of settings will operate
the fan as long as the remote control (N) and receiver
(M) are set to the same position.
□
M
Insert the receiver (M) into the mounting bracket (B)
with the flat side of the receiver (M) facing the
ceiling.
B
9
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-877-527-0313 for further assistance.
Assembly — Hanging the Fan (continued)
7
Making the electrical connections
1
WARNING: To avoid possible electrical shock, ensure the
electricity is turned off at the circuit breaker or main fuse box
before wiring.
WARNING: Check to see that all connections are tight,
including the ground, and that no bare wire is visible at the
wire nuts, except for the ground wire.
Black
White
Black
White
Follow the steps below to connect the fan to your house
supply wires. Secure the wire nuts (FF) supplied with your
fan by wrapping the connections with electrical tape.
Green
Green
M
Motor to receiver electrical connections:
□ Connect the black wire from the fan to the black wire
marked "TO MOTOR L" from the receiver (M).
□
□
Connect the white wire from the fan to the white wire
marked "TO MOTOR N" from the receiver (M).
Black
Black
Connect the blue wire from the fan to the blue wire
marked "For Light" from the receiver (M).
Receiver to house supply wires electrical connections:
□ Connect the black (hot) wire from the ceiling to the
black wire marked "AC in L" from the receiver (M).
□
Connect the white (neutral) wire from the ceiling to
the white wire marked "AC in N" from the receiver
(M).
□
If your outlet box (1) has a ground wire (green or bare
copper), connect it to the fan ground wires; otherwise,
connect the hanging ball (E) ground wire to the
mounting bracket (B).
□
Secure the wire connection with a plastic wire nut
(FF) provided with the electrical hardware.
□
After connecting the wires, spread them apart so that
the green and white wires are on one side of the
outlet box (1) and the black and blue wires are on the
other side. Carefully tuck the wire connections up
into the outlet box (1).
FF (x6)
H
10
Blue White
Blue White
Assembly — Hanging the Fan (continued)
7
Securing the fan motor assembly to the mounting bracket
□
Remove one screw (LL) from the mounting bracket (B) and loosen the other screw (LL) approximately 1/4 turn.
□
Carefully raise the canopy (C) up to the mounting bracket (B), and ensure the loosened screw (LL) is inserted into the key hole on
the canopy (C). Rotate the canopy (C) clockwise.
□
Secure the canopy (C) by replacing the screw (LL) previously removed and tightening the screw (LL) previously loosened.
□
Place the canopy cover (D) on the canopy (C), and rotate the canopy cover (D) clockwise until it locks into position.
B
LL
C
LL
D
11
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-877-527-0313 for further assistance.
Assembly — Attaching the Fan Blade Assemblies
8
Fastening the blade assemblies
to the fan motor assembly
□
Attach the fan blades (A) to the blade holders (I) by
using three blade screws (AA) and fiber washers (BB).
Tighten screws (AA) and fiber washers (BB) securely.
□
Insert the blade holder (I) through the slots on the fan
motor assembly (H).
□
Attach the blade holder (I) to the fan motor assembly (H)
using the blade holder screws (CC) and tighten them
securely.
□
Repeat this step for the other blade holders (I).
AA
BB
A
I
H
I
CC
12
Assembly — Installing the Light Kit
9
10
Attaching the light kit plate
to the mounting ring
Attaching the 17W LED Assembly
to the light kit plate
□
Remove one of three screws (MM) from the fan motor
assembly (H) mounting ring, and loosen the other two
screws (MM), but do not remove.
□
Remove one of three screws (NN) from the light kit
plate (J), and loosen the other two screws (NN), but do
not remove.
□
Place the key holes from the light kit plate (J) over the
two screws (MM) previously loosened from the fan
motor assembly (H) mounting ring. Turn the light kit
plate (J) until it locks in place at the narrow section of
the key holes. Secure by tightening the two screws
(MM) previously loosened and the one screw (MM)
previously removed.
□
While holding the 17W LED assembly (K) under your fan,
firmly snap the wire connection plugs (PP) together.
□
Place the key holes from the 17W LED assembly (K) over
the two screws (NN) previously loosened from the light kit
plate (J). Turn the17W LED assembly (K) until it locks in
place at the narrow section of the key holes. Secure by
tightening the two screws (NN) previously loosened
and the one screw (NN) previously removed.
H
J
PP
J
K
NN
MM
13
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-877-527-0313 for further assistance.
Assembly — Installing the Light Kit (continued)
12
Installing the glass shade
□
Attach the glass shade (L) to the light kit plate (J) by twisting tightly.
J
L
14
Operation
REMOTE CONTROL OPERATING INSTRUCTIONS
Install a 12V battery (P) into the remote control (N). To prevent
damage to the remote control, remove the battery if not used for
long periods of time.
N
WARNING: Do not short-circuit, disassemble, heat up,
connect improperly, or dispose of used batteries in fire. Do
not recharge or mix batteries with used or other battery
types. Immediately remove used batteries.
Restore power to the ceiling fan and test for proper operation.
□
HI, MED, LOW buttons: Sets the fan speed.
□
“
□
“ ” button: Turns the light ON or OFF. Press and hold the
button to set the desired brightness.
P
” button: Turns the fan off.
REVERSE FUNCTION BUTTON OPERATING
INSTRUCTIONS
The reverse switch is located on the surface of the fan
motor assembly.
This switch controls directions: forward (switch left) or reverse
(switch right).
NOTE: Wait for the fan to stop before reversing the direction
of the blade rotation.
Warm weather - (Counterclockwise Direction) A downward air flow
creates a cooling effect. This allows you to set your air conditioner
on a higher setting without affecting your comfort.
Cool weather - (Clockwise Direction) An upward air flow moves
warm air off the ceiling. This allows you to set your heating unit on
a lower setting without affecting your comfort.
15
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-877-527-0313 for further assistance.
Operation (continued)
INSTALLING THE REMOTE CONTROL HOLDER
□
Attach the remote control holder (O) with the two remote control
holder mounting screws (EE).
O
EE
Care and Cleaning
Do
□
Do not
Check the support connections, brackets, and blade
attachments twice a year. Ensure they are secure.
Because of the fan’s natural movement, some
connections may become loose over time. It is not
necessary to remove the fan from the ceiling.
□
Clean your fan periodically. Use only a soft brush or
lint-free cloth to avoid scratching the finish. The plating is
sealed with a lacquer to minimize discoloration or
tarnishing.
□
(Optional) Apply a light coat of furniture polish to the wood
blades.
□
(Optional) Cover small scratches with a light application of
shoe polish.
16
□
Do not use water when cleaning. Water could damage the
motor, or the wood, or possibly cause an electrical shock.
□
Do not apply oil to your fan or motor. The motor has
permanently-lubricated sealed ball bearings.
Troubleshooting
WARNING: Ensure the power is off at the electrical
panel box before you attempt any repairs. Refer to the section
“Making the Electrical Connections” on page 11.
Problem
The fan will not start.
The fan sounds noisy.
The remote control is
not working.
The fan wobbles.
Solution
□
Check main and branch circuit fuses or breakers.
□
Check line wire connections to the fan and switch wire connections in the switch housing.
□
Check to make sure the dip switches from the remote control and receiver are set to the same
frequency.
□
Make sure all motor housing screws are snug.
□
Make sure the screws that attach the fan blade arm to the motor hub are tight.
□
Make sure wire nut connections are not rattling against each other or the interior wall of the switch
housing.
□
Allow a 24-hour "breaking-in" period. Most noises associated with a new fan disappear during this
time.
□
If using the ceiling light kit, make sure the screws securing the glassware are tight. Check that the light
bulb is also secure.
□
Make sure there is a short distance from the ceiling to the canopy. It should not touch the ceiling.
□
Make sure your ceiling box is secure and rubber isolator pads are used between the mounting bracket
and outlet box.
□
Do not connect the fan with wall mounted variable speed control(s).
□
Check to make sure the dip switches from the remote control and receiver are set to the same frequency.
□
Check that all blade and blade arm screws are secure.
□
Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a
point on the ceiling above the tip of one of the blades. Measure from a point on the center of each blade
to the point on the ceiling. Rotate the fan until the next blade is positioned for measurement. Repeat for
each blade. Measurements deviation should be within 1/8 in. Run the fan for 10 minutes.
□
Use the enclosed blade balancing kit if the blade wobble is still noticeable.
18
17
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-877-527-0313 for further assistance.
Service Parts
AA
I
HH
II
J
BB
A
B
JJ
K
CC
L
KK
C
D
E
DD
M
F
EE
G
N
FF
O
GG
LL
MM
H
P
Description
Part Description
Blade
Mounting bracket
AA
Blade screw
B
BB
Fiber washer
C
Canopy
CC
Blade holder screw
D
Canopy cover
DD
Balance kit
E
Hanger ball
EE
Remote control holder mounting screws
F
Downrod
Coupling cover
FF
Wire nuts
GG
HH
Cross pin
Hitch pin
Part
A
G
H
I
Fan motor assembly
Blade holder
II
Lock pin
J
Light kit plate
JJ
Hanger ball set screw
K
17W LED assembly
KK
Fan motor assembly coupling set screw
L
Glass shade
LL
Mounting bracket screw
M
Receiver
MM
Fan motor assembly mounting ring screw
N
Remote control
NN
Light kit plate screw
O
P
Remote control holder
12V battery
18
NN
Questions, problems, missing parts? Before returning to the store,
call Home Decorators Collection Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
1-877-527-0313
HOMEDEPOT.COM/HOMEDECORATORS
Retain this manual for future use.