AireRyder BE-LKD003AW-C Use and Care Manual

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
BE-LKD003
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless
additional support is provided for the fan.
Fig.1
Black(Blue Wire)
Wire Nut
Smooth Wire
Washer
Center Plug
Fig.2
Black(Blue Wire)
Wire Nut
Smooth Wire
Washer
Center Plug
Fig.3
Motor
Switch Box
Arm
White Wire
Ridged Wire
Hex Nut
Screw
Switch Box Cover
Nipple(-b)
Light Kit
Motor
Switch Box
White Wire
Ridged Wire
Hex Nut
Screw
Switch Box
Glass Holder
Glass Shade
Pull Chain
Socket Ring
Switch Box Cover
Nipple(-b)
Light Kit
For Light Kit:
1. Adjust the arms of the fixture according to the drawing of the package.
Important:
a. The arms should be positioned with equal distances between them.
b. The arms should be fixed securely.
2. Remove the switch box cover from the switch box of the fan by loosing the three screws.
(See Fig.1 & Fig.2)
3. Unscrew the center plug from the switch box cover and discard it.
4. Thread the wires through the switch box cover, washer and hex nut, then attach nipple(-b)
of the light kit to the hole of the switch box cover and secure it with the washer and hex nut.
5. Pull out the wires from the switch box. Make wire connections using the wire nuts:
---The smooth (marked) wire from the light kit to the black or blue wire from the fan.
---The ridged (unmarked) wire from the light kit to the white wire from the fan.
---Carefully tuck the wires back into the switch box cover.
6. Restore the switch box cover back to the switch box using the three screws.
7. Attach the glass shades upward to the glass holders, then secure them with the socket rings.
(See Fig.3)
8. Install bulbs (not included). See relamping label at socket area or packaging for maximum
allowed wattage.
9. Turn on the power at the main fuse or circuit breaker box.
TM
(You can control the lights with the pull chain)
BE-LKD003 --- Page 1
060612
For Chandelier:
Outlet Box
House Grounding Wire
Wire Nut
Hex Nut
Washer
Mounting Strap
Green Grounding Screw
Mounting Screw
Nipple(-a)
1. Attach nipple(-a) to the mounting strap, then secure it with
a washer and hex nut.
2. Attach the mounting strap to the outlet box by using two
mounting screws.
3. Take out the parts from the hardware package for the
Canopy
chandelier.
Top Loop
4. Follow the step 1 as For Light Kit. (Page 1)
Collar
5. Secure the loop to nipple(-b).
Loop Lock
6. Choose the length of the chain you need, then weave the
Chain
fixture wire and the fixture grounding wire through the chain
Fixture Grounding Wire
links. Connect one end of the chain with the loop using a
Loop Lock
loop lock.
7. Secure the top loop to nipple(-a).
Fixture Wire
8. Thread the fixture wire and fixture grounding wire through
Loop
the collar, canopy, top loop, nipple(-a) and mounting strap.
Nipple(-b)
9. Connect the other end of the chain with the top loop using
Light Kit
Glass Holder
the other loop lock.
10. Pull out the outlet wires and the house grounding wire
from the outlet box. Make wire connections using the
wire nuts:
---The smooth wire (marked) from fixture to black
wire from power source.
---The ridged wire (unmarked) from fixture to white
wire from power source.
---Attach the fixture grounding wire to the mounting
strap with the green grounding screw. Then
connect it to the house grounding wire with
a wire nut.
Carefully tuck the wires back into the outlet box.
Pull Chain
11. Attach the canopy to the mounting strap by inserting
Glass Shade
the top loop and secure it with the collar.
Socket Ring
12. Attach the glass shades upward to the glass holders,
then secure them with the socket rings.
13. Install bulbs (not included). See relamping label at socket area or packaging for maximum
allowed wattage.
14. Turn on the power at the main fuse or circuit breaker box.
(You can control the lights with the pull chain.)
TM
BE-LKD003 --- Page 2
060612