AireRyder LK36453BN-C Instructions / Assembly

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
LK36453
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless
additional support is provided for the fan.
Fig.1
Motor
Black or Blue Wire
Switch Box
Wire Nut
Black
Washer
Center Plug
White Wire
White Wire
Hex Nut
Screw
Switch Box Cover
Nipple
Fixture
Fig.2
Screw
Black or Blue Wire
Wire Nut
Black
Motor
Switch Box
White Wire
Terminal (Groove)
Terminal ( Tongue)
White Wire
Switch Box Cover
Hex Nut
Cap
Washer
Nipple
Set Screw
(6 x 32 20mmL)
Fig.3
Motor
Glass Holder
Glass Shade
For Light Kit:
1. Remove the switch box cover from the switch
box of the fan by loosing the three screws.
2. Unscrew the center plug from the switch box
Pull Chain
cover and discard it.
Socket Ring
3. For fan style that is shown in Fig.1: Attach the
nipple of the light kit to the hole of the switch
box cover, then thread the wires through the washer and hex nut, then secure them tightly.
4. For fan style that is shown in Fig.2: Thread the fixture wire through the washer, hex nut and
the switch box cover. Then attach the cap to the switch box cover, then secure it with two
set screws (6x32 20mmL).
5. Pull out the wires from the switch box. Make wire connections using the wire nuts:
---The black wire from light kit to the black or blue wire from the fan.
---The white wire from light kit to the white wire from the fan.
---Carefully tuck wires back into the switch box.
6. Restore the switch box cover back to the switch box using the three screws.
7. Attach the glass shades to glass holders, then secure them with socket rings. (See Fig.3)
8. Install bulbs (not included). See relamping label at socket area or packaging for maximum
allowed wattage.
9. Turn on the power at the main fuse or circuit breaker box.
(You can control the lights with the pull chain.)
TM
LK36453 --- Page 1
060218
For Ceiling Light: (See Fig.4 & Fig.5)
Hex Nut
Washer
Cap
Nipple
Fixture
Fig.4
Mounting Parts for Ceiling Light
1. Take out the hex nut, washer, two bolt nuts, grounding
pad and canopy from the hardware package for ceiling
Outlet Box
light.
House Grounding Wire
2. Unscrew and remove the hex nut, washer and the cap
Wire Nut
from the nipple. ( See Fig.4)
Screw
3. Attach the canopy with the open side facing upward to
Mounting Strap
the fixture by inserting the nipple, then secure it with a
Lock Nut
Green Grounding Screw
washer, grounding pad and hex nut.
Mounting Screw
4. Attach two screws to the mounting strap, then secure
Fixture Grounding Wire
them with two lock nuts. Adjust the length of the screws
Hex Nut
Grounding Pad
if necessary.
Washer
5. Attach the mounting strap to the outlet box by using two
Canopy
mounting screws.
6. Pull out the outlet wires and the house grounding wire
Bolt Nut
from the outlet box. Make wire connections using the
Nipple
wire nuts:
---The black wire from fixture to the black wire from the
Fig.5
outlet box.
---The white wire from fixture to the white wire from the
outlet box.
---Attach the fixture grounding wire to the mounting strap with the green grounding screw. Then connect
it to the house grounding wire with a wire nut.
Carefully tuck the wires back into the outlet box.
7. Attach the canopy to the mounting strap by inserting two screws, then secure them with the bolt nuts.
8. Follow steps 7~9 as for Light Kit.
TM
LK36453--- Page 2
060218