Hunter 99183 Instructions / Assembly

LED Bowl Fitter
Installation Manual
Model 99183
Compatible with:
2xxxx Types A - Z
51000-58999 fan series
59500-59999 fan series
Select Casablanca Fans
MA011-01 • 09/26/13
1.888.830.1326
BEFORE YOU BEGIN
Read entire installation instructions carefully before
beginning installation and save these instructions.
Switch
Housing
Your light kit is compatible with most ceiling fans. The light kit will attach to the fan’s
switch housing. Begin on page 3 where you will choose the type of switch housing that
most closely resembles the one on your fan. From there, you will be directed to the set of
assembly instructions that are appropriate for installing the light kit to your fan.
READ AND SAVE THESE INSTRUCTIONS
This product conforms to UL Standard 507.
WARNINGS
w.1 - To reduce the risk of fire, electrical shock, or personal injury,
mount fan directly from building structure and/or an outlet box marked
acceptable for fan support of 70 lbs. (31.8 kg) and use the mounting screws
provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your
fan, disconnect the power by turning off the circuit breakers to the outlet
box and associated wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent warning device,
such as a tag, to the service panel.
CAUTIONS
c.1 - All wiring must be in accordance with national and local electrical codes
ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.
2
MA011-01 • 09/26/13
er
Pow
n
r
Tu
OFF
1.888.830.1326
WHICH ASSEMBLY METHOD WILL I USE?
Choose one of the four images below that most closely resembles the switch
housing on your fan; then follow the instructions under the image.
Cap
Screw
Switch
Housing
Screw
Switch
Housing
Cap
If your fan’s switch housing cap
resembles this one, remove the cap
screws with a Phillips head screwdriver.
Then follow the TYPE-A ASSEMBLY
INSTRUCTIONS on pages 4-5.
Switch
Housing
Screw
Switch
Housing
Cap
If your fan’s switch housing cap resembles
this one, remove the whole switch
housing by removing the switch housing
screws with a Phillips head screwdriver.
Remove the two cap screws from the
inside of the switch housing. Reinstall
the switch housing. Tighten the switch
housing screws. Then follow the TYPE-A
ASSEMBLY INSTRUCTIONS on pages 4-5.
Plug
Button
Plug
Button
If your fan’s switch housing cap
resembles this one, remove the whole
switch housing by removing the switch
housing screws with a Phillips head
screwdriver. Remove the plug button.
Then follow the TYPE-B ASSEMBLY
INSTRUCTIONS on pages 6-7.
Switch
Housing
Screw
If your fan’s switch housing cap resembles
this one, remove the whole switch
housing by removing the switch housing
screws with a Phillips head screwdriver.
Remove the plug button using a standard
screwdriver. Then follow the TYPE-C
ASSEMBLY INSTRUCTIONS on pages 8-9.
3
MA011-01 • 09/26/13
1.888.830.1326
TYPE-A ASSEMBLY INSTRUCTIONS
1
2
Switch
Housing
Wire
Connector
If your fan does not have pin connectors on
the wires coming from the switch housing,
install the wiring harness provided. Using
the provided wire connectors connect the
white wire from the fan to the white wire
from the wire harness and connect the
black or blue wire from the fan to the black
wire from the wire harness.
Using the single pin connectors, connect
the black or blue wire from the fan to the
black wire from the light kit. Connect the
white wire from the fan to the white wire
from the light kit.
3
4
Light Kit
Cap
Light Kit
Screw
Light
Fixture
Remove the light kit screws attaching the
light kit cap to the light fixture.
Light Kit
Screw
Attach the light kit to the switch housing
by re-installing the light kit screws
through the fixture and light kit cap into
the switch housing.
4
MA011-01 • 09/26/13
Do not allow the light kit to hang
only by the wire connections!
1.888.830.1326
TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED)
5
6
Fan Pull
Chain
Globe
Globe
Keeper
Grommeted
Hole
Finial Cap
Light Pull
Chain
Finial
Installing the globe - Press the globe
(sold separately) and globe keeper flush
against the metal plate. Thread the light
pull chain through the hole in the center
of the finial cap and thread the fan pull
chain through the hole in the side of the
cap. Finally, thread only the light pull
chain through the hole in the finial and
screw the finial onto the threaded rod.
If necessary, attach the extension chain
provided to the fan pull chain coming
from the switch housing. Then feed the
end of the extension chain through the
grommeted hole in the light kit.
7
Installing the Pull chain pendant Attach the pull chain pendants to the
end of the short chains coming from the
switch housing and the light kit. Turn on
power. Your installation is complete!
5
MA011-01 • 09/26/13
1.888.830.1326
TYPE-B ASSEMBLY INSTRUCTIONS
1
2
Switch
Housing
Light Kit
Screw
Wire
Connector
If your fan does not have pin connectors on
the wires coming from the switch housing,
install the wiring harness provided. Using
the provided wire connectors connect the
white wire from the fan to the white wire
from the wire harness and connect the
black or blue wire from the fan to the black
wire from the wire harness.
Remove the light kit screws attaching the
light kit cap to the light fixture.
3
4
Bad Wolf
Switch
Housing
Light Kit
Screw
Feed the light kit wires through the
center hole in the switch housing. Then
attach the switch housing to the light kit
by installing the light kit screws through
the light fixture and light kit cap and into
the bottom of the switch housing.
Using the single pin connectors, connect
the black or blue wire from the fan to the
black wire from the light kit. Connect the
white wire from the fan to the white wire
from the light kit.
6
MA011-01 • 09/26/13
Do not allow the light kit to hang
only by the wire connections!
1.888.830.1326
TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED)
5
6
Fan Pull
Chain
Grommeted
Hole
Switch
Housing
Screw
Light Pull
Chain
Lift the light kit assembly up so that the
screw holes in the lower switch housing
line up with the holes in the upper switch
housing. Install the switch housing
screws and tighten securely.
If necessary, attach the extension chain
provided to the fan pull chain coming
from the switch housing. Then feed the
end of the extension chain through the
grommeted hole in the light kit.
7
8
Globe
Globe
Keeper
Finial Cap
Finial
Installing the globe - Press the globe (sold
separately) and globe keeper flush against
the metal plate. Thread the light pull chain
through the hole in the center of the finial cap
and thread the fan pull chain through the hole
in the side of the cap. Finally, thread only the
light pull chain through the hole in the finial
and screw the finial onto the threaded rod.
Installing the pull chain pendant Attach the pull chain pendants to the
end of the short chains coming from the
switch housing and the light kit. Turn
power on. Your installation is complete.
7
MA011-01 • 09/26/13
1.888.830.1326
TYPE-C ASSEMBLY INSTRUCTIONS
1
2
Washer
and Nut
Threaded
Rod
Switch
Housing
Wire
Connector
If your fan does not have pin connectors on
the wires coming from the switch housing,
install the wiring harness provided. Using
the provided wire connectors connect the
white wire from the fan to the white wire
from the wire harness and connect the
black or blue wire from the fan to the black
wire from the wire harness.
Feed the wires through the switch
housing cap, washer, and nut. Then
install the switch housing cap by twisting
clockwise onto the threaded rod. Install
the washer and nut onto threaded rod
and tighten securely.
3
4
Light Kit
Cap
Screws
Using the single pin connectors, connect
the black or blue wire from the fan to the
black wire from the light kit. Connect the
white wire from the fan to the white wire
from the light kit.
LED Ring
Remove the screws attaching the LED
ring to the light kit cap. Do not discard the
screws.
8
MA011-01 • 09/26/13
Do not allow the light kit to hang
only by the wire connections!
1.888.830.1326
TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED)
5
6
Upper
Switch
Housing
LED
Ring
Lift the light kit assembly up so that the
screw holes in the lower switch housing
line up with the holes in the upper switch
housing. Install the switch housing
screws and tighten securely.
7
Install the screws removed in Step 4
through the LED Ring and into the light
kit cap.
8
Fan Pull
Chain
Grommeted
Hole
Screws
9
Globe
Globe
Keeper
Finial Cap
Light Pull
Chain
If necessary, attach the
extension chain provided
to the fan pull chain
coming from the switch
housing. Then feed the
end of the extension chain
through the grommeted
hole in the light kit.
Finial
Installing the globe - Press the globe (sold
separately) and globe keeper flush against
the metal plate. Thread the light pull chain
through the hole in the center of the finial cap
and thread the fan pull chain through the hole
in the side of the cap. Finally, thread only the
light pull chain through the hole in the finial
and screw the finial onto the threaded rod.
9
MA011-01 • 09/26/13
Installing the pull chain
pendant - Attach the pull
chain pendants to the end
of the short chains coming
from the switch housing
and the light kit. Turn
power on. Your installation
is complete.
1.888.830.1326
TROUBLESHOOTING
Lights don’t come on.
• Make sure that the bulbs are properly installed.
• Make sure power switch is on.
• Pull the pull chain to make sure it is on.
• Check the circuit breaker to ensure the power is turned on.
• Check the pin connections in the light kit.
• Refer to the fan manual for locating the fan’s wiring. Verify that the light and power
wires are correctly connected to the ceiling and the light kit.
ONE YEAR WARRANTY
This product is warranted to the original purchaser by Casablanca Fan Company/
Hunter Fan Company against defects in material and workmanship for one (1)
year from date of purchase. During the warranty period, we will repair or, at our
option, replace a defective product at no charge. For information on how to obtain
service, contact the Casablanca/Hunter Service Department by calling our tollfree number at 888-830-1326. Damage to the product caused by mishandling,
improper installation or modification is not covered by this warranty. This warranty
is given in lieu of all other warranties expressed or implied. Some states do not allow
limitations of time on an implied warranty, therefore the above limitations may not
apply in every case. This warranty states specific legal rights which may vary from
state to state.
If you have problems installing or operating your light kit, do not return this product
to the dealer. Call our Consumer Affairs Hotline.
888-830-1326
10
MA011-01 • 09/26/13