Casablanca K4BA-11 Instructions / Assembly

R
FAN COMPANY
READ AND SAVE THESE INSTRUCTIONS
INSTRUCTIONS FOR MOUNTING INTEGRATED LIGHT FIXTURE
K4, K4B, K4BR, K4S, KG4T
WARNING: To reduce the possibility of electrical shock be sure that the power
is turned off at its source(fuse or circuit breaker). All electrical components
must be installed in accordance with national and local electrical codes.
To reduce the risk of fire and electrical shock, this light fixture should be used
only with UL, ETL & CUL Certified Casablanca ceiling fans.
IMPORTANT: Before discarding any packing material locate the following items:
Fixture
Light Bulb(s)
Dimensions (w/glass)
Weight
K4
4-60W A15 Med. Base
7” h x 20” w
2 lbs
K4B
4 - 50w “R” Reflector
6 1/4” h x 10 to 19” w
3 lbs
K4BR
4 - 50w “R” Reflector
7” h x 11 to 19” w
2 lbs
K4S
4 - 60w A15 Med. Base
6” h x 20 1/2” w
2 lbs
KG4T
4 - 60w A15 Med. Base
5 1/2” h x 17 1/2”w
4 lbs
INSTALLATION
For fan models ending in A, D, M, R,
T, V, W: (For K4BR — See Step 10
First!!)
1. Remove the cover from fan by removing two brass
8-32 screws and save these screws for attaching light
fixture. Remove plastic wire nuts from switch housing
wires and strip 1/2" insulation from both wires (black or
blue, and white). This cover will not be reused. See
FIG. 1
NOTE: If installing this light fixture on a 3 Speed
pull-chain model fan, a separate pull-chain switch
(included with the fan) must be installed. Refer to
the following installation instructions, otherwise
skip to step 4.
2. Remove the plastic plug from the fan switch housing. Install the light on-off switch by inserting the chain
through hole, from the inside. Pass the switch threads
into the hole and screw the knurl nut onto the switch.
Hand tighten firmly. See FIG. 2
3. Attach the blue wire from the fan to one of the blue
wires on the switch by twisting the bare ends of the
wires together. Secure the splice by threading on one
of the wire nuts provided. Test the secureness of the
splice by pulling on the wire nut.
SWITCH
HOUSING
COVER
8-32 SCREW
FIG. 1
WHITE WIRE
KNURL NUT
PLASTIC PLUG
BLUE WIRE
WIRE NUT
PULL-CHAIN
SWITCH
FIG. 2
89443470
Jul. 03
4. While holding light fixture up to the fan,
attach the wires from the fan switch housing
and the wires from the light fixture together
(black-to-black or blue-to-black and white-towhite) by twisting the bare ends of the wires
together. Then secure the splices by threading on the wire nuts provided. Test the secureness of each splice by pulling on the wire
nut. See FIG. 3
5. Attach the light fixture to the fan switch
housing using the two brass 8-32 screws,
insuring guide pins are properly located into
fan switch housing.
Caution: Make sure no wires are pinched
between light fixture and switch housing.
Tighten the screws to secure light fixture.
6. Install glass if applicable. (not included
except for KG4T). Loosen the thumbscrews
on each shadeholder align glass inside
shadeholder as far as it will go and tighten
thumbscrews equally around the glass. Make
sure glass is snug and locked down tight so
that the glass will not rattle when the fan is in
operation.
7. Install the light bulbs. Do not exceed
the maximum wattage indicated on
the light fixture.
8. Connect fob chain to light pull chain.
9. Installing glass on KG4T:
a. Remove socket locking ring from the
socket. Set aside.
b. Install glass shade by aligning the
longer edge of the glass at the top
and installing socket locking ring onto
socket. Turn until glass is snug against
the shadeholder and socket locking
ring is tight.
10. Installing glass on K4BR:
(Do this step before installing on fan)
a. Install rings onto end of bullet shade
by first removing the screws, align rings with
holes in shade and re-install screws.
b. Tighten srews with a screwdriver until snug.
c. Return to Step 1.
WHITE WIRE
BLACK OR BLUE
WIRE
BLACK WIRE
GUIDE PIN
LIGHT FIXTURE
FIG. 3
THUMB SCREW
OPTIONAL:
IF CENTER LIGHT DESIRED
SEE THE INSTRUCTIONS
INCLUDED WITH THE K2
LIGHT FIXTURE
Light Bulb Socket
Glass Shade
Example
Shade Holder Ring