AireRyder LK30304RBZ Instructions / Assembly

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
LK30304
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless
additional support is provided for the fan.
Fig.1
Black(Blue Wire)
Wire Nut
Smooth Wire
Washer
Center Plug
Motor
Switch Box
White Wire
Ridged Wire
Hex Nut
Screw
Switch Box Cover
Nipple
Light Kit
Fig.2
Screw
Black(Blue Wire)
Wire Nut
Smooth Wire
Motor
Switch Box
White Wire
Terminal (Groove)
Terminal ( Tongue)
Ridged Wire
Switch Box Cover
Cap Screw
Cap
Set Screw
(6 x 32 20mmL)
Nipple
Fixture
Fig.3
Motor
Glass Holder
For Light Kit:
Glass Shade
1. Remove the switch box cover from the switch
box of the fan by loosing the three screws.
Socket Ring
Pull
Chain
2. Unscrew the center plug from the switch box
cover and discard it.
3. For fan as Fig.1: Attach the nipple of the light kit to the hole of the switch box cover. Thread
the wires through the washer and hex nut, then secure them tightly.
4. For fan as Fig.2: Unscrew the cap screw to remove the cap from the light kit, then secure it
upward to the switch box cover using the set screws (6x32 20mmL). Thread the wires of the
light kit through the cap and switch box cover. Attach the light kit to the cap using the cap
screw.
5. Pull out the outlet wires from the switch box. Make wire connections using the wire nuts:
---The smooth (marked) wire from the light kit to the blue wire from the fan.
---The ridged (unmarked) wire from the light kit to the white wire from the fan.
---Carefully tuck the wires back into the switch box cover.
6. Restore the switch box cover back to the switch box using the three screws.
7. Attach the glass shades upward to the glass holders, then secure them with the socket rings.
(See Fig.3)
8. Install bulbs (not included). See relamping label at socket area or packaging for maximum
allowed wattage.
9. Turn on the power at the main fuse or circuit breaker box.
(You can control the lights with the pull chain.)
TM
LK30304 --- Page 1
070424
For Chandelier:
Fig.4
1. Take out the cap from the hardware package for chandelier.
2. Thread the fixture wires through the cap, washer and stem.
3. Attach the cap and the washer onto the light kit by inserting
nipple(-b), then secure them with the stem.(See Fig.4)
4. Attach nipple(-a) to the mounting strap, then secure it with a
washer and hex nut.
5. Attach the mounting strap to the outlet box using two
mounting screws.
6. Choose the length of the chain you need, then weave the
fixture wire and the fixture grounding wire through the
chain links. Connect one end of the chainwith the
loop using a loop lock.
7. Secure the top loop to nipple(-a).
8. Thread the fixture wire and fixture grounding wire
through the collar, canopy, top loop, nipple(-a) and
mounting strap.
9. Connect the other end of the chain with the top loop
by using the other loop lock.
10. Pull out the outlet wires and the house grounding wire
from the outlet box. Make wire connections using the
wire nuts:
---The smooth wire (marked) from fixture to the black
wire from power source.
---The ridged wire (unmarked) from fixture to the white
wire from power source.
---Attach the fixture grounding wire to the mounting
strap with the green grounding screw. Then connect
it to the house grounding wire with a wire nut.
Carefully tuck the wires back into the outlet box.
11. Attach the canopy to the mounting strap by
inserting the top loop and secure it with the
collar.
12. Attach the glass shades upward to the
glass holders, then secure them with the
socket rings.
13. Install bulbs (not included). See
relamping label at socket area or
Pull Chain
packaging for maximum allowed
wattage.
14. Turn on the power at the main fuse or circuit breaker box.
(You can control the light with the pull chain.)
Stem
Washer
Cap
Light Kit
Nipple(-b)
Outlet Box
House Grounding Wire
Wire Nut
Hex Nut
Washer
Mounting Strap
Green Grounding Screw
Mounting Screw
Nipple(-a)
Canopy
Top Loop
Collar
Loop Lock
Chain
Fixture Grounding Wire
Loop Lock
Fixture Wire
Loop
Fixture
Glass Holder
Glass Shade
Socket Ring
TM
LK30304 --- Page 2
070424