Sea Gull Lighting 6016-12 Installation Guide

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-322
022309
IMPORTANT SAFETY INSTRUCTIONS
*OUTLET BOX
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
Read instructions carefully.
Save these instructions.
CLEANING
*GROUND
WIRE
*WIRE
CONNECTORS
MOUNTING
BAR (A)
*OUTLET BOX
SCREWS
NIPPLE (C)
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
NUT (B)
GREEN
GROUNDING
SCREW (D)
GROUND
WIRE (M)
SCREW
COLLAR (E)
CANOPY (G)
SCREW
COLLAR
RING (F)
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
CHAIN (I)
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
FIXTURE LOOP (H)
STEP 1:
Attach fixture loop (H) to top of fixture (if applicable).
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 2:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Attach screw collar (E) to nipple (C).
STEP 3:
GLASS
PANELS (L)
CAGE (J)
RETAINING
SCREWS
(K)
Using 2 pairs of pliers, open one link of chain (I) and connect it to the
fixture loop (H) at the top of the fixture. (If applicable).
STEP 4:
Slide the screw collar ring (F) and canopy (G), in that order, over
chain (I). Open one link on the other end of the chain (I) and attach it
to the screw collar (E) which has been mounted to the ceiling nipple
(C). BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
FIGURE 1
*NOT INCLUDED
INSTALLATION (continued)
HC-322
STEP 5:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 7:
After wires are connected, tuck them carefully inside outlet box.
Raise canopy (G) against ceiling and thread the screw collar ring (G)
to the screw collar (E).
STEP 8:
Place glass panels (L) in cage (J), raise the cage (J) to the hood and
secure with retaining screw (K). (If applicable).
NOTE: There is a variation in all castings - in some cases the glass
panels may be slightly loose when installed - you may want to tape it
in place. Two (2) sided tape has been supplied for this purpose remove protective paper from each side of tape - place on upper end
of glass - install and press against casting.
STEP 9:
Install lamp.