Sea Gull Lighting 94562-965 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
RAIL
RAIL
ADAPTER (Q)
COLLAR (C)
*OUTLET
*BOX
GROUNDING AND MOUNTING BAR
LOCK UP FOR OPTIONAL
MONO-POINT CANOPY
*OUTLET BOX
MONOPOINT
CANOPY
(B)
WIRE
CONNECTORS
SPLICE
COMPARTMENT
(F)
*OUTLET BOX
SCREWS
*GROUND WIRE
STEM (S)
SHADE (T)
STRAIN RELIEF (O)
DECORATIVE
RING (E)
MOUNTING
BAR (A)
NIPPLE (D)
NUT &
LOCKWASHER
(R)
RETAINING
RING (U)
FIGURE 1
COLLAR (C)
*NOT INCLUDED
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
FIGURE 2
*NOT INCLUDED
NOTE: This pendant can be hung either from a Transitions Series
rail (not supplied) or from the supplied canopy. Follow the
instructions for the appropriate mounting method.
For use with the 120V Transitions track series by
Sea Gull Lighting.
Caution – To reduce the risk of burn during relamping remove from
the track before relamping.
Minimum distance from the front of the lamp to combustible
surfaces is 8".
Make sure all connections are tight.
Dimming halogen lamps greatly reduces lamp life.
To reduce the risk of FIRE or INJURY TO PERSONS: Turn off and
allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact switch only when turning on.
Do not touch hot lens, guard, or enclosure.
Keep lamp away from materials that may burn.
Do not touch the lamp at any time. Use a soft cloth. Oil from skin
may damage lamp.
Do not operate the luminaire fitting with a missing or damaged
shield.
Save these instructions.
LR-117
062308
www.SeaGullLighting.com
ASSEMBLING PENDANT/SHORTENING PENDANT (Fig. 1)
LR-117
1. Determine length of pendant and shorten cable. Be sure to
add 5" for electrical connections when installing as a monopoint.
2. Unthread splice compartment (F). Remove wiring
connections and unthread top portion of splice compartment
(F) from pendant.
3. Set strain relief collar and top of splice compartment at
desired location on cut cable. NOTE: Strain relief collar is
threaded and should be threaded up and down cable. Be
sure ¹/₄" of cable jacket is protruding out of strain relief
collar. Secure in place by tightening the two set screws.
4. Use supplied allen wrench to set glass support at desired
location on stem (S). Thread glass retaining ring (U) onto
glass support in order to secure decorative ring (E) and
shade (T).
5. Make connections between socket leads and pendant cable
using wire nuts inside the splice compartment (F) – Black to
Black/White to White/Ground to Ground. Make sure no
wires are left exposed and carefully tuck wire nuts into
bottom half of splice compartment (F).
6. Close splice compartment (F) by threading the two halves
together.
7. Install lamp. Thread supplied lamp enclosure over lamp.
FOR MONO-POINT INSTALLATION (Fig. 2)
1. Remove rail adapter (Q) by cutting wire below rail adapter
(Q).
2. Slide collar (C), canopy (B), nut and lockwasher (R),
mounting bar (A) and nipple (D) over wire.
3. Install strain relief (O). Tighten strain relief set screw with a
flat head screw driver.
4. Attach mounting bar (A) to outlet box using outlet box
screws (not supplied).
5. Make electrical connections using wire nuts of other UL
listed device:
a. House Black to Fixture Black
b. House White to Fixture White
Take house ground wire and fixture ground wire and wrap
around the green grounding screw located on the mounting
bar (A). Secure by tightening the green grounding screw.
Make sure no wires are left exposed and carefully tuck
wires into outlet box.
6. Raise canopy (B) to cover outlet box and thread collar (C)
to nipple (D) in order to secure.
ATTACH PENDANT TO RAIL (Fig. 3)
1. Unthread cap (I) from rail adapter (Q).
2. Making sure contacts (G) will align with conductors (H) on
rail, set the bottom of the rail adapter (Q) to the bottom of
the rail and “roll” rail adapter (Q) up onto the rail.
3. Close hinged door of rail adapter (Q) up onto rail. Thread
cap (I) back onto rail adapter (Q).
RAIL INSTALLATION
CORRECT
CONTACTS (G)
INCORRECT
CONTACTS (G)
CAP (I)
CAP (I)
FIGURE 3
CONDUCTOR (H)
CONDUCTOR (H)