advertisement
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
• Be sure the electricity to the system you are working on is turned off; either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty, listing and create a potential safety hazard.
• If you are unclear as to how to proceed, contact a qualified electrician.
• You don't need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• Read instructions carefully.
• To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system able to support the weight of the fixture
• Save these instructions.
*HOUSE
GROUND
WIRE
NIPPLE (C)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. Parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts are included, as shown in figure 1. Be careful not to misplace any of the screws or parts which are needed to install this fixture.
HC-1434
103008
*OUTLET BOX
*WIRE
CONNECTORS
MOUNTING BAR (A)
*OUTLET BOX
SCREWS
NUT (B)
GROUND WIRE (F)
COLLAR (E)
CANOPY (H)
COLLAR RING (I)
CHAIN (J)
FIXTURE LOOP (K)
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Attach fixture loop (K) to top of fixture.
STEP 2:
Secure mounting bar (A) to outlet box with outlet box screws (not supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed above nut (B). Thread nipple (C) into mounting bar (A) and secure with nut (B). Attach collar (E) to nipple (C).
STEP 3:
Using 2 pairs of pliers, open one link of chain (J) and connect it to the fixture loop (K) at the top of the fixture.
STEP 4:
Slide the collar ring (I) and canopy (H), in that order, over chain (J).
Open one link on the other end of the chain (J) and attach it to the collar (E). BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
GLASS
RETAINING
RING (L)
FIGURE 1
SHADE (G)
DIFFUSER
RING (M)
*NOT INCLUDED
INSTALLATION (continued) HC-1434
STEP 5:
A. Use a listed wire connector to connect the fixture hot wire (black wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can remove the wires, carefully re-do the wiring connection.
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to be inserted into the hole with two raised dimples provided on the mounting bar (A). Wrap the ground wire (F) from the fixture and the ground wire from the outlet box (bare metal or green insulated wire) around the green grounding screw (D) on the mounting bar (A) if uninsulated wire is on the mounting bar (A), connect the ground wire
(F) from the fixture and the outlet box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 7:
After wires are connected, tuck them carefully inside outlet box and then raise the canopy (H) against ceiling and thread the collar ring (I) to the collar (E).
STEP 8:
Rest diffuser ring (M) on lip of shade (G). Raise shade (G) to socket and secure by threading glass retaining ring (L) onto socket.
STEP 9:
Install lamp (not supplied).
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project