Sea Gull Lighting 61251-824 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
GROUNDING AND MOUNTING BAR LOCK UP
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS
REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
*OUTLET BOX
*GROUND WIRE
*WIRE
CONNECTORS
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Read instructions carefully. If you are
unclear as to how to proceed, consult a qualified electrician.
MOUNTING
BAR (A)
ASSEMBLY
*OUTLET BOX
SCREWS
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figures 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
FIGURE 1
FOR
STEM
MOUNT
GREEN
GROUNDING
SCREW (D)
NUT (B)
NIPPLE (C)
*NOT SUPPLIED
*OUTLET BOX
FIGURE 2
*NOT INCLUDED
*WIRE
CONNECTORS
NUT (W )
MOUNTING
SCREWS (I)
LOCK WASHER (H)
CANOPY (G)
NIPPLE (M)
CANOPY LOOP (S)
CANOPY (G)
SCREW
COLLAR RING (F)
CHAIN (Y)
COUPLING (J)
FIXTURE LOOP (X)
SOCKET ASSEMBLY (U)
FIGURE 3
ROD ASSEMBLY (E)
ASSEMBLY FOR CHAIN HUNG
STEP 1:
Install fixture loop (X) onto socket assembly (U).
STEP 2:
Feed the fixture wire from the socket assembly (U), through the fixture
loop (X), chain (Y) and canopy loop (S) (mounted on canopy (G)).
GLASS (P)
RETAINING
RING (T)
Note: This fixture can be hung using 1, 2, or 3 rods.
Select the number of rods desired.
FOR STEM MOUNT
STEP 1:
Secure rods together (if applicable).
STEP 2:
Feed the fixture wire from the socket assembly (U), through: the rod
assembly (E), and coupling (J) (mounted on canopy (G)).
STEP 3:
Secure rod assembly (E) to coupling (J), and socket assembly (U).
Be sure not to damage the fixture wire.
Installation And
Safety Instruction
HC-883 120604
Line art shown may not exactly match the fixture enclosed. However,
the installation instructions do apply to this fixture.
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_______________
INSTALLATION
HC-883
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
FOR STEM MOUNT AND CHAIN HUNG
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are
exposed above nut (B). Thread nipple (C) into mounting bar (A) and
secure with nut (B).
FOR CHAIN HUNG ONLY
STEP 1:
Using 2 pair of pliers, open one link of chain (Y) and connect it to the
fixture loop (X) at the top of the fixture.
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 2:
Lace fixture wire up through entire chain (Y) and pass through
canopy loop (S). We recommend lacing wire up through every
other link of chain (Y).
WIRING
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. DO NOT twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw
the connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
STEP 2:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is
to be inserted into the hole with two raised dimples provided on the
mounting bar. Wrap the ground wire from the fixture (if supplied) and
the ground wire from the outlet box (bare metal or green insulated
wire) around the green grounding screw (D) on the mounting bar.
If uninsulated wire is on the mounting bar, connect the ground wire
from the fixture (if supplied) and the outlet box to it using a small
wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications. The
listing mark of Underwriters on the product identifies products
manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 1:
Make sure no bare wires can be seen outside wire connectors.
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
FOR STEM MOUNT AND CHAIN HUNG
STEP 1:
After wires are connected, tuck them carefully inside outlet box and then
raise the canopy (G) against ceiling allowing and screw the screw collar
ring (F) to nipple.
STEP 2:
Install lamp.
STEP 3:
Raise glass (P) to fixture and secure with retaining ring (T).
CLEANING
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
ORDERING PARTS
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.