Sea Gull Lighting 65662-839 Installation Guide

Installation And Safety Instructions
HC-1436
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
112508
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
To reduce the risk of fire, electric shock, or personal injury, mount
to outlet box or supporting system able to support the weight of
the fixture.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
Read instructions carefully.
Save these instructions.
*OUTLET BOX
*WIRE CONNECTORS
STEP 2
NUT (B)
*GROUND WIRE
MOUNTING BAR (A)
*OUTLET BOX
SCREWS
NIPPLE (C)
CLEANING
CANOPY (D)
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
STEP 4
ORDERING PARTS
SCREW COLLAR (E)
SCREW COLLAR
RING (F)
CHAIN (G)
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
BEFORE YOU BEGIN
STEP 3
FIXTURE LOOP (H)
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
STEP 1
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Thread fixture loop (H) to fixture.
STEP 2:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 5 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Thread screw collar (E) to nipple (C).
STEP 3:
Using 2 pairs of pliers or chain break, open one link of chain (G) and
connect it to the fixture loop (H) at the top of the fixture. Chain
should be opened outward, do not twist.
DIFFUSER (J)
STEP 4:
Slide the screw collar ring (F) and canopy (H), in that order, over
chain (G). Open one link on the other end of the chain (G) and attach
it to the screw collar (E) which has been mounted to the nipple (C).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
FIGURE 1
*NOT SUPPLIED
WIRING
HC-1436
STEP 5:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
*OUTLET BOX
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (F) from the fixture and the
ground wire from the outlet box (bare metal or green insulated wire)
around the green grounding screw (D) on the mounting bar (A) if
uninsulated wire is on the mounting bar (A), connect the ground wire
(F) from the fixture and the outlet box to it using a small wire
connector (not supplied). NEVER CONNECT GROUND WIRE TO
BLACK OR WHITE POWER SUPPLY WIRES.
STEP 5
*WIRE CONNECTORS
STEP 6
*GROUND WIRE
MOUNTING BAR (A)
NUT (B)
*OUTLET BOX
SCREWS
NIPPLE (C)
STEP 7
CANOPY (D)
SCREW COLLAR (E)
SCREW COLLAR
RING (F)
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
CHAIN (G)
STEP 7:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (D) against ceiling and thread the screw collar
ring (F) to the screw collar (E).
STEP 8:
Install lamps (not supplied).
STEP 9:
Place diffuser (J) into decorative ring (L). Raise decorative ring (L) to
the fixture ring (M) so mounting studs (O) protrude through both
rings. Secure by threading retaining screws (N) onto mounting stud
(O).
STEP 10:
Place washers over threaded holes of top diffuser mounting area.
Place washers onto top diffusers (W) and secure by threading top
diffuser retaining screws (V) through top diffusers (W), washers, and
threaded holes of top diffuser (W) mounting area.
TOP
DIFFUSERS
(W)
FIXTURE
RING (M)
DECORATIVE
RING (L)
DIFFUSER
RETAINING
SCREWS (V)
STEP 10
DECORATIVE
RING (L)
DIFFUSER (J)
STEP 9
MOUNTING
STUDS (O)
FIGURE 3
RETAINING
SCREWS (N)
*NOT INCLUDED
FIGURE 2
*NOT SUPPLIED