Sea Gull Lighting 94571-71 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
CAP (E)
RAIL
STRAIN
RELIEF
SCREW (P)
RAIL
ADAPTER (R)
COLLAR (J)
*OUTLET
BOX
GROUNDING AND MOUNTING BAR
LOCK UP FOR OPTIONAL
MONO-POINT CANOPY
*OUTLET BOX
CANOPY
(G)
WIRE
CONNECTORS
SPLICE
COMPARTMENT
(I)
STEM (M)
*OUTLET BOX
SCREWS
*GROUND WIRE
STRAIN RELIEF (H)
MOUNTING
BAR
(F)
HEX NUT & LOCK
WASHER (D)
SOCKET (Q)
LAMP
ENCLOSURE
(B)
FIGURE 1
*NOT INCLUDED
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
For use with the 120V Transitions track series by Sea Gull Lighting.
Caution – To reduce the risk of burn during relamping remove from
the track before relamping.
If you are unclear as to how to proceed, contact a qualified
electrician.
Minimum distance from the front of the lamp to combustible
surfaces is 8".
Make sure all connections are tight.
Dimming halogen lamps greatly reduces lamp life.
To reduce the risk of a burn during relamping, remove from the
track before relamping.
Turn off and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact switch only when turning on.
Do not touch hot lens, guard, or enclosure.
Keep lamp away from materials that may burn.
Do not touch the lamp at any time. Use a soft cloth. Oil from skin
may damage lamp.
Do not operate the luminaire fitting with a missing or damaged
shield.
Save these instructions.
NIPPLE
(A)
MONOPOINT
CANOPY
(G)
COLLAR (O)
FIGURE 2
*NOT INCLUDED
NOTE: This pendant can be hung either from a Transitions Series
rail (not supplied) or from the supplied canopy. Follow the
instructions for the appropriate mounting method.
LR-120
062308
www.SeaGullLighting.com
ASSEMBLING PENDANT/SHORTENING PENDANT
LR-120
1. Determine length of pendant and shorten cable from the
splice compartment (I). Be sure to add 5" for electrical
connections when installing as a mono-point.
2. Unthread splice compartment (I). Carefully remove wire
connections located in the splice compartment (I). Unthread
bottom half of splice compartment (I) and remove from stem
(M). Install optional shade (not supplied) by following
instructions supplied with shade.
3. Set top of splice compartment (I) and strain relief collar at
desired location. NOTE: Strain relief collar is threaded and
should be threaded up and down cable. Be sure ¹⁄₄" of cable
jacket is protruding out of strain relief collar. Secure in place
by tightening the two set screws.
4. Make connections between socket leads and pendant cable
using wire nuts inside the splice compartment:
a. Black to Black
b. White to White
c. Ground to Ground
Make sure no wires are left exposed and carefully tuck wire
nuts into bottom half of splice compartment (I).
5. Close splice compartment (I) by threading the two halves
together.
6. Install lamp and lamp enclosure (B) to socket.
FOR MONO-POINT INSTALLATION – (Fig.2)
1. Remove rail adapter (R) by cutting wire just below rail
adapter (R).
2. Slide collar (O), canopy (G), mounting bar (F), nipple (A),
hex nut and lock washer (D), over wire to the top of the
splice compartment (I) (in that order).
3. Install strain relief (H) to wire. Tighten set screw with a flat
head screwdriver.
4. Secure mounting bar (F) to outlet box with outlet box
screws (not supplied).
5. Make electrical connections using wire nuts or other UL
listed device. Be sure that no wires are left exposed.
a. House Black to Fixture Black
b. House White to Fixture White
Wrap fixture ground wire and house ground wire around the
green grounding screw located on the mounting bar (F).
Secure by tightening the green grounding screw. Carefully
tuck wires into outlet box.
6. Raise canopy (G) against ceiling and secure by threading
collar (O) to threaded nipple (A).
ATTACH PENDANT TO RAIL – (Fig. 3)
1. Unthread cap (E) from rail adapter (R).
2. Making sure contacts (K) will align with conductors (L) on
rail, set the bottom of the the rail adapter (R) to the bottom
of the rail and “roll” rail adapter (R) up onto the rail.
3. Install fixture to rail by closing rail adapter (R) over rail.
Replace cap (E) over top of rail adapter (R) and thread cap
(E) back onto rail adapter (R).
4. Tighten strain relief screw (P) located just below rail adapter
(R).
RAIL INSTALLATION
CORRECT
CONTACTS (K)
INCORRECT
CONTACTS (K)
CAP (E)
CAP (E)
FIGURE 3
CONDUCTOR (L)
CONDUCTOR (L)