Hampton Bay SC-1DAK-HBU Instructions / Assembly

TROUBLESHOOTING:
Bulb will not light
Fuse blows or circuit
breaker trips when light
is turned on
Possible Cause
Corrective Action
1. Bulb is burned out
1. Replace light bulb
2. Power is off
2. Make sure power supply
is on
3. Faulty wire connection
3. Check wiring
Crossed wires or power
wire is grounding out
Check wire connections
INSTRUCTION MANUAL
INTERIOR 1-LIGHT WALL SCONCE
DAKOTA
HOME DEPOT SKU 647-066 (UPC 773546224680)
SATIN NICKEL FINISH
PRODUCT MAINTENANCE:
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use
clean water, never a solvent) to wipe the shade and surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning
off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or
slightly dampened clean cloth (use clean water, never a solvent) to wipe the inside
shade and interior surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry
soft cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship
for a period of five (5) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the
manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident,
modifications, alterations, neglect or mishandling. This warranty shall not apply to any product that is
found to have been improperly installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident,
misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material
or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface
and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and
specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other
than the warranty contained herein. The manufacturer specifically disclaims any liability and shall
not be liable for any consequential or incidental loss or damage, including but not limited to any labor
expense costs involved in the replacement or repair of said product.
Page 6
Page 1
Thank you for purchasing this Hampton Bay interior decorative lighting. This product
has been manufactured with the highest standards of safety and quality.
FEATURES:
Curved panel shades are composed of glass with a marbled pattern, set against a
rectangular metal backplate.
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION
(not included):
Safety goggles
Wire Strippers
Wire Cutters
Flathead
Screwdriver
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer Service
Team at 1-877-527-0313 or visit www.homedepot.com. Please reference your
SKU 647-066 or (UPC 773546224680).
CAUTION:
1. Before starting installation of this fixture or removal of a previous fixture, disconnect
the power by turning off the circuit breaker or by removing the fuse at the fuse
box.
Phillips
Screwdriver
Electrical Tape
ADDITIONAL PARTS (included):
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL
QUESTIONS.
3. If you have any non-electrical questions about this fixture, please contact our
Customer Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU 647-066 or (UPC 773546224680).
4. Keep your receipt and these Instructions for Proof of Purchase.
2. Backplate
3. Screws (x2)
4. Wire Nuts (x3)
5. Ground Screw
6. Mounting Screws
8. Locknuts (x2)
9. G9 Bulb 60W
10. Glass
(x2)
Page 2
Page 3
ASSEMBLY INSTRUCTIONS:
1. Carefully unpack the fixture; lay out all parts on clean surface.
ASSEMBLY:
2. Turn off power at main fuse box.
3. Install backplate (2) to junction box (1) with 2 mounting screws (6) supplied. Make
sure black and white wires of junction box runs through the middle opening of the
backplate.
4. Fasten open end of ground wire (bare copper or green wire), to ground wire or
ground screw of junction box or ground screw (5) on backplate.
1. Junction Box
(not included)
10. Glass
5. Connect black and white wires of power supply to black and white wires of the
fixture.
4. Wire Nuts (x3)
NOTE: All wire connections should be made with wire nuts or marrettes (included) (4)
and pushed back into junction box.
2. Backplate
6.Mount the canopy (7) over the 2 screws (3) of backplate. Secure with 2 locknuts (8).
GLASS AND BULB INSTALLATION:
5. Ground Screw
9. G9 Bulb 60W
(included)
1.Using a tissue or glove, install 60W max Shielded G9 bulb (included) (9) otherwise
oil from fingers will decrease the lift of the bulb drastically.
2.Slip glass (10) into end slots over bulb.
3. Screws (x2)
6.Mounting Screws (x2)
7. Canopy
8. Locknuts (x2)
Page 4
Page 5