Sea Gull Lighting 49150BLE-962 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
ASSEMBLY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be
Read instructions carefully. If you are unclear as to how to proceed,
consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
*OUTLET BOX
STEP 1:
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
NOTE: FOR FIXTURES PROVIDED WITH 75˚ C OR 90˚C
SUPPLY WIRE WARNING ONLY-(THESE WARNINGS
ARE PROVIDED ON THE U.L. LABEL AND ON THE
FIXTURE CARTON): RISK OF FIRE. MOST
DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE
RATED 60˚ C. CONSULT A QUALIFIED ELECTRICIAN
BEFORE INSTALLING.
DIFFUSER (I)
*WIRE CONNECTORS
*OUTLET BOX SCREWS
NIPPLE (F)
BACKPLATE LIP (G)
BACKPLATE (A)
MOUNTING BAR (D)
NUT (E)
CAP NUT (H)
*NOT SUPPLIED
(FIG. 1)
IF SUPPLY WIRES ARE LOCATED WITHIN 3” OF
BALLAST, USE WIRE RATED FOR AT LEAST 90˚C.
GROUNDING AND MOUNTING BAR LOCK UP
*OUTLET BOX
NUT (E)
GREEN
GROUNDING
SCREW (G)
NIPPLE (F)
*OUTLET BOX
SCREWS
*GROUND WIRE
*NOT INCLUDED
MOUNTING BAR (D)
*WIRE CONNECTORS
FIGURE 2
Installation And
Safety Instruction
HC-937
102005
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_______________
INSTALLATION
HC-937
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
CAUTION: DO NOT BEND TABS THAT SECURE
GLASS. BENDING TABS WILL PREVENT THE GLASS
FROM SITTING PROPERLY.
STEP 1:
Using outlet box screws (not supplied) fasten mounting bar [D] to
outlet box through slots in mounting bar [D].
STEP 2:
Thread nut [E] onto nipple [F] so that 5 threads are exposed above
nut [E]. Thread that end of the nipple [F] into mounting bar [D] and
tighten nut [E] against mounting bar [D].
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (D). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (G) on the mounting bar (D). If uninsulated ground wire is on the universal mounting
bar, connect the ground wire from the fixture (if supplied) and the outlet box to it using a small wire connector (not supplied) (See Figure 2).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications. The
listing mark of Underwriters on the product identifies products manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 3:
Make sure no bare wires can be seen outside wire connectors.
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 1:
After wires are connected, tuck them carefully inside the outlet box.
Position back plate (A) over nipple (F) and secure in place with cap
nut (H).
STEP 2:
Install lamps.
STEP 3:
Slide the edge of diffuser (I) into backplate lip (G), making sure it
securely fits in there.
CLEANING
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (SQUARE & RIDGED)
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do Not twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw
the connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
BALLAST REPLACEMENT
TURN POWER OFF.
Carefully remove glass by the following glass installation instructions
in reverse. Separate the 120v connection of the ballast from the
supply wire by removing wire nuts. Disconnect the secondary
ballast wires to the socket by inserting a small screwdriver into
the rear of the socket release the wire lead.
Remove ballast mounting screws and remove ballast from fixture
assembly. Replace ballast with the same model, secure ballast to
fixture assembly, insert secondary ballast wires by pushing them
into the rear of the socket, and make proper wiring connections to
the supply wire.