Sea Gull Lighting 44475-962 Installation Guide

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
BEFORE YOU BEGIN
HC-1448
112408
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
INSTALLATION
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and figure 2. Be careful not to
misplace any of the screws or parts which are needed to install this
fixture.
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Run fixture mounting screws (B) through holes in universal mounting
bar (A) all the way down to their heads.
STEP 2:
Using outlet box screws (not supplied) fasten universal mounting bar
(A) to outlet box through slots in universal mounting bar (A). Be sure
fixture mounting screws (B) are perfectly vertical so fixture hangs
straight.
*OUTLET
BOX
*OUTLET
BOX
SCREWS
FIXTURE
MOUNTING
SCREWS (B)
STEP 2
STEP 1
UNIVERSAL
MOUNTING
BAR (A)
FIGURE 1
*NOT INCLUDED
INSTALLATION (continued)
HC-1448
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 3:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the
universal mounting bar (A). Wrap the ground wire from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or
green insulated wire) around the green grounding screw (G) on the
universal mounting bar (A). Tighten the green grounding screw (G) to
secure. If uninsulated wire is on the universal mounting bar (A),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied). NEVER
CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
*SUPPLY
GROUND
WIRE
STEP 3
FIXTURE
MOUNTING
SCREWS (B)
STEP 5:
Make sure no bare wires can be seen outside wire connectors.
STEP 6:
After wires are connected, tuck them carefully inside outlet box. Push
the canopy (C) firmly over the fixture mounting screws (B) and
against the wall. Secure canopy (C) in place by threading cap nuts
(D) onto fixture mounting screws (B).
STEP 7:
Place glass (E) onto socket and secure in place by threading
retaining ring (F) to socket.
STEP 8:
Install lamps (not supplied).
FIXTURE
GROUND
WIRE
GREEN
GROUNDING
SCREW (G)
CANOPY (C)
STEP 6
CAP NUTS (D)
GLASS (E)
STEP 4
*WIRE
CONNECTOR
STEP 7
UNIVERSAL
MOUNTING
BAR (A)
FIGURE 2
RETAINING
RING (F)
*NOT INCLUDED