Sea Gull Lighting 4135-962 Installation Guide

Installation And Safety Instructions
HC-516
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
CLEANING
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
071708
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
Proper wiring is essential for the safe operation of this fixture.
Read instructions carefully.
Save these instructions.
NOTE: FOR FIXTURES PROVIDED WITH 75˚ C OR 90˚C SUPPLY WIRE
WARNING ONLY-(THESE WARNINGS ARE PROVIDED ON THE U.L.
LABEL AND ON THE FIXTURE CARTON): RISK OF FIRE. MOST
DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60˚ C.
CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
CAUTION: DO NOT BEND TABS THAT SECURE GLASS. BENDING
TABS WILL PREVENT THE GLASS FROM SITTING PROPERLY.
IF SUPPLY WIRES ARE LOCATED WITHIN 3" OF BALLAST, USE WIRE
RATED FOR AT LEAST 90˚C.
STEP 1:
Using outlet box screws (not supplied) fasten mounting bar (D) to
outlet box through slots in mounting bar (D).
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
STEP 2:
Thread nut (E) onto nipple (F)so that 5 threads are exposed above
nut (E). Thread that end of the nipple (F)into mounting bar (D) and
tighten nut (E)against mounting bar (D).
*WIRE
CONNECTORS
GREEN
GROUNDING
SCREW (G)
NIPPLE
(F)
*OUTLET
BOX
DIFFUSER (I)
*GROUND
WIRE
BACKPLATE
LIP (G)
CAP NUT (H)
BACKPLATE (A)
MOUNTING NUT (E)
BAR (D)
FIGURE 1
*OUTLET
BOX
SCREWS
*NOT INCLUDED
INSTALLATION (continued)
HC-516
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
STEP 5:
After wires are connected, tuck them carefully inside the outlet box.
Position back plate (A) over nipple (F) and secure in place with cap
nut (H).
STEP 6:
Install lamps.
STEP 7:
(If applicable.) Slide the edge of diffuser (I) into backplate lip (G),
making sure it securely fits in there.
GROUP A:
CONNECT TO BLACK HOUSE WIRE
GROUP B:
CONNECT TO WHITE HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped or
ridged and less tracer wire is round in shape or smooth
(Seen best when viewed from wire end). To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector, If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (D). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (G) on the
mounting bar (D). If uninsulated ground wire is on the universal
mounting bar, connect the ground wire from the fixture (if supplied)
and the outlet box to it using a small wire connector (not supplied)
(See Figure 2).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.