Sea Gull Lighting 49652BLE-962 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
BEFORE YOU BEGIN
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don't need special tools to install this fixture. Be sure to
follow the steps in the order given.
Save these instructions.
*OUTLET BOX
UNIVERSAL MOUNTING
MOUNTING SCREWS (F)
BAR (D)
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
CANOPY (I)
CAP NUTS (H)
(CONCEALED BY SHADE)
SOCKET
ASSEMBLY
(B)
GREEN
GROUNDING
SCREW (G)
SHADE (A)
GROUND
WIRE
GLASS RETAINING
SCREWS (C)
FIGURE 1
*NOT INCLUDED
GROUNDING & UNIVERSAL
MOUNTING BAR LOCK UP
*OUTLET BOX
SCREWS
*OUTLET BOX
MOUNTING
SCREWS (F)
GROUND
WIRE
*WIRE
*CONNECTOR
FIGURE 2
GREEN
GROUNDING
SCREW (G)
UNIVERSAL
MOUNTING
BAR (D)
*NOT SUPPLIED
Installation And Safety
Instruction
HC-1127 071107
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_________
INSTALLATION
HC-1127
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Insert mounting screws (F) in threaded holes of universal mounting
bar (D). Run mounting screws (F) all the way down to heads.
STEP 2:
Using outlet box screws (not supplied) fasten universal mounting bar
(D) to outlet box through slots in universal mounting bar (D). Be sure
the mounting screws (F) are perfectly vertical so fixture hangs
straight.
STEP 3:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G)
is to be inserted into the hole with two raised dimples provided on
the universal mounting bar (D). Wrap the ground wire from the fixture
(if supplied) and the ground wire from the outlet box (bare metal
or green insulated wire) around the green grounding screw (G)
on the universal mounting bar (D) if uninsulated wire is on the
universal mounting bar (D), connect the ground wire from the
fixture (if supplied) and the outlet box to it using a small wire
connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 1:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
Make sure no bare wires can be seen outside wire connectors. After
wires are connected, tuck them carefully inside outlet box. Push the
canopy (I) firmly over the mounting screws (F) and against the wall.
Secure canopy (I) in place with cap nuts (H).
STEP 2:
Place shade (A) on socket assembly (B) and secure by threading
glass retaining screws (C) into socket assembly (B).
STEP 3:
Install lamp/ballast (J) (Fig. 3) by twisting into socket.
CLEANING
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
FIXTURES WITH A
ONE PIECE LAMP / BALLAST
COMBINATION
ONE PIECE
LAMP/
BALLAST (J)
SOCKET (K)
FIGURE 3