Sea Gull Lighting 44853-782 Installation instructions

Add to my manuals
2 Pages

advertisement

Sea Gull Lighting 44853-782 Installation instructions | Manualzz

Installation And Safety Instructions

Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________

HC-1301

012208

IMPORTANT SAFETY INSTRUCTIONS

• Be sure the electricity to the system you are working on is turned off; either the fuse removed or the circuit breaker set at off.

• Use of other manufacturers components will void warranty, listing and create a potential safety hazard.

• If you are unclear as to how to proceed, contact a qualified electrician.

• You don't need special tools to install this fixture.

• Be sure to follow the steps in the order given.

• Read instructions carefully.

• Save these instructions.

BEFORE YOU BEGIN

Carefully remove the fixture from the carton and check that all parts are included, as shown in figure 1 and 2. Be careful not to misplace any of the screws or parts which are needed to install this fixture.

BACKPLATE (C) GREEN

GROUNDING

SCREW (G)

*GROUND

WIRE

MOUNTING

SCREWS (F)

CANOPY (I)

CAP NUTS (E) SOCKET

CUP (B)

FIGURE 1

RETAINING

RING (H)

SHADE (A)

*NOT INCLUDED

INSTALLATION HC-1301

IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET

BOX.

STEP 1:

Place backplate (C) against wall and mark location for drywall anchors. Remove backplate (C) and drill appropriate sized holes into drywall.

STEP 2:

Pull supply wires through appropriate opening in backplate (C).

Place backplate (C) against wall and secure by installing drywall screws (not supplied) into drywall anchors.

STEP 3:

A. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:

BLACK WHITE

STEP 4:

GROUNDING INSTRUCTIONS:

The green grounding screw (G) is to be inserted into the hole with two raised dimples provided on the backplate (C). Wrap the ground wire from the fixture (if supplied) and the ground wire from the outlet box (bare metal or green insulated wire) around the green grounding screw (G) on the backplate (C) if uninsulated wire is on the backplate (C), connect the ground wire from the fixture (if supplied) and the outlet box to it using a small wire connector (not supplied).

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

FINAL ASSEMBLY

STEP 1:

Make sure no bare wires can be seen outside wire connectors. After wires are connected, tuck them carefully inside outlet box. Push the fixture firmly over the mounting screws (F) and against the wall.

Secure canopy (I) in place by threading cap nuts (E) onto fixture mounting screws (F).

STEP 2:

Place shade (A) on socket cup (B) and secure by threading retaining ring (H) onto socket.

STEP 3:

Install lamps.

CLEANING

To clean, wipe fixture body with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

*

PARALLEL WIRE (ROUND & SMOOTH)

*

PARALLEL WIRE (SQUARE & RIDGED)

*Note: When parallel wire is used, the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth.

(Seen best when viewed from wire end.) To separate wires, grasp the ends of each wire and pull apart.

B. Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box.

DO NOT twist wires together before using wire connectors.

C. Fit a wire connector (not supplied) over the wires and thread the connector clockwise until you feel a firm resistance.

D. Gently try to remove the wires from the connector. If you can remove the wires, carefully re-do steps B and C, as above and check again for a firm connection.

E. Connect the fixture wire from group B to the white wire from the outlet box in the same manner.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. Parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement