Sea Gull Lighting 44122-820 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
ASSEMBLY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER SET AT OFF.
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
GENERAL
You don't need special tools to install this fixture. Be sure to follow
the steps in the order given. Read instructions carefully. If you are
unclear as to how to proceed, consult a qualified electrician.
*NOT INCLUDED
FIGURE 1
CANOPY (I)
MOUNTING BAR (J)
GLASS (J)
NIPPLE (F)
CAP NUT (H)
*WIRE NUTS
GLASS
RETAINING
RING (M)
GROUNDING & UNIVERSAL MOUNTING
BAR LOCK UP
UNIVERSAL
MOUNTING
BAR (J)
*WIRE
CONNECTOR
NIPPLE (F)
*OUTLET BOX
SCREWS (K)
Installation And
Safety Instruction
HC-889
112205
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
FIGURE 2
*NOT SUPPLIED
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
ITEM#_______________
INSTALLATION
HC-889
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Using outlet box screws (not supplied) fasten mounting bar (D) to
outlet box through slots in mounting bar (D).
STEP 2:
Thread nut (E) onto nipple (F) so that 5 threads are exposed above
nut (E). Thread that end of the nipple (F) into mounting bar (D) and
tighten nut (E) against mounting bar (D).
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (D). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (G) on the
mounting bar (D) if uninsulated wire is on the mounting bar (D),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications. The
listing mark of Underwriters on the product identifies products
manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 1:
Make sure no bare wires can be seen outside wire connectors.
STEP 2:
After wires are connected, tuck them carefully inside outlet box.
Push the fixture firmly over the mounting nipple (F) and against the
wall. Secure canopy (I) in place with cap nut (H).
STEP 3:
Place glass (J) in holder and secure in place by screwing on retaining ring (M).
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
GROUP B: CONNECT TO WHITE
HOUSE WIRE
STEP 4:
Install lamps.
WHITE
CLEANING
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.