Sea Gull Lighting 4411-185 Installation Guide

HC-532
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
BEFORE YOU BEGIN
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Proper wiring is essential for the safe operation of this fixture.
To reduce the risk of fire, electric shock, or personal injury, mount to
outlet box or supporting system able to support the weight of the
fixture.
Save these instructions.
SHADES (E)
FIXTURE
ARM (D)
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
CANOPY (C)
GLASS
RETAINING
RING (F)
CAP
NUTS (G)
SHADE
DECORATIVE (I)
FIGURE 1
*NOT INCLUDED
GROUNDING & UNIVERSAL
MOUNTING BAR LOCK UP
*OUTLET BOX
SCREWS
*OUTLET BOX
MOUNTING
SCREWS (F)
GROUND
WIRE
*WIRE
*CONNECTOR
FIGURE 2
103007
GREEN
GROUNDING
SCREW (G)
UNIVERSAL
MOUNTING
BAR (D)
*NOT SUPPLIED
INSTALLATION
HC-532
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Insert fixture mounting screws (B) into threaded holes of universal
mounting bar (A). Run fixture mounting screws (B) all the way down
to the heads.
STEP 2:
Place universal mounting bar (A) against outlet box (not supplied)
and secure in place using outlet box screws (not supplied). Be sure
the mounting screws are perfectly vertical so fixture hangs straight.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture (K) and the
ground wire from the outlet box (bare metal or green insulated
wire) around the green grounding screw (G) on the mounting bar
(A) if uninsulated wire is on the mounting bar (A), connect the
ground wire from the fixture (K) and the outlet box to it using a
small wire connector (not supplied).
NEVER CONNECT GR OUND WIRE TO BLA CK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 1:
Make sure no bare wires can be seen outside wire connectors.
After wires are connected, tuck them carefully inside the outlet box.
Position canopy (C) over mounting screws (B) and secure in place
by threading cap nuts (G) onto fixture mounting screws (B).
STEP 2:
Remove rubber washer from socket. Place shade (E) over socket.
Place rubber washer over socket and secure by threading retaining
ring (F) onto socket.
STEP 3:
Install lamps. Attach shade decorative (I) to shade (E).
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector . If you can
remove the wires, carefully re-do steps B and C, as above and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.