Sea Gull Lighting 49851BLE-782 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
BEFORE YOU BEGIN
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
*OUTLET BOX
UNIVERSAL
MOUNTING
BAR (D)
GREEN
GROUND
GROUNDING WIRE
SCREW (G)
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
CANOPY (I)
CAP
NUT (E)
SOCKET
CUP (B)
SHADE
(A)
NIPPLE (F)
NUT (C)
FIGURE 1
RETAINING RING (H)
*NOT INCLUDED
GROUNDING & UNIVERSAL
MOUNTING BAR LOCK UP
GREEN
GROUNDING
SCREW (G)
*OUTLET BOX
SCREWS
NIPPLE (F)
GROUND
WIRE
NUT (C)
Installation And Safety
Instruction
HC-1376 052708
*WIRE CONNECTOR
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
UNIVERSAL
MOUNTING BAR (D)
FIGURE 2
*NOT SUPPLIED
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_________
HC-1376
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Thread nipple (F) to center of universal mounting bar (D) so five
threads are exposed past universal mounting bar (D). Thread nut (C)
to universal mounting bar (D) to secure.
STEP 2:
Using outlet box screws (not supplied) fasten universal mounting bar
(D) to outlet box through slots in universal mounting bar (D).
STEP 3:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is
to be inserted into the hole with two raised dimples provided on the
universal mounting bar (D). Wrap the ground wire from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or
green insulated wire) around the green grounding screw (G) on the
universal mounting bar (D)and tighten the green grounding screw to
secure. If uninsulated wire is on the universal mounting bar (D),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
A. Take note of the color of the wire(s) on your fixture. identify which
group your fixture wire(s) falls into and connect the wires according to
the directions below:
STEP 1:
Make sure no bare wires can be seen outside wire connectors. After
wires are connected, tuck them carefully inside outlet box. Push the
fixture firmly over the mounting nipple (F) and against the wall. Secure
canopy (I) in place by threading cap nut (E) onto nipple (F).
STEP 2:
Place shade (A) on socket cup (B). Thread retaining ring (H) onto
socket (K) to secure shade (A).
STEP 3:
Hold lamp (J) by base and install to socket (K) by twisting gently.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
*Note: When parallel wire is used, the tracer wire is square shaped or
ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against the
black wire from the outlet box. DO NOT twist wires together before
using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering
parts.
FIXTURES WITH A
ONE PIECE LAMP /
BALLAST
COMBINATION
ONE PIECE
LAMP/ BALLAST
COMBINATION (J)
SOCKET (K)
FIGURE 3