Sea Gull Lighting 44661-839 Installation Guide

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don't need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
Read instructions carefully.
Save these instructions.
BEFORE YOU BEGIN
HC-1430
081908
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
INSTALLATION
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Insert fixture mounting screws (F) into universal mounting bar (D) and
run fixture mounting screws (F) all the way down to the heads.
STEP 2:
Using outlet box screws (not supplied) fasten universal mounting bar
(D) to outlet box through slots in universal mounting bar (D). Make
sure fixture mounting screws (F) are perfectly horizontal so fixture
hangs straight.
*OUTLET BOX
*OUTLET
BOX
SCREWS
STEP 2
STEP 1
UNIVERSAL
MOUNTING
BAR (D)
FIGURE 1
FIXTURE
MOUNTING
SCREWS (F)
*NOT INCLUDED
INSTALLATION (continued)
HC-1430
STEP 3:
FINAL ASSEMBLY
STEP 5:
A. Use a listed connector to connect the fixture hot wire (black wire,
or round and smooth tracer) to the supply hot wire.
B. Use a listed connector to connect the fixture common wire (white
wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
Make sure no bare wires can be seen outside wire connectors. After
wires are connected, tuck them carefully inside outlet box. Push the
fixture firmly over the mounting screws (F) and against the wall.
Secure canopy (I) in place with cap nuts (E).
STEP 6:
Place shade (A) on socket cup (B) and secure by threading retaining
ring (C) onto socket.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the
universal mounting bar (D). Wrap the ground wire from the fixture (H)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (G) on the universal
mounting bar (D) and tighten the green grounding screw (G) to
secure. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
*OUTLET BOX *HOUSE
UNIVERSAL GREEN
GROUND WIRE MOUNTING GROUNDING
BAR (D)
SCREW (G)
STEP 7:
Install lamps (not supplied).
FIXTURE
GROUND
WIRE (H)
STEP 3
CANOPY
(I)
STEP 4
SOCKET
CUP (B)
STEP 5
SHADE
(A)
*WIRE
CONNECTORS
*OUTLET
BOX
SCREWS
FIXTURE
MOUNTING
SCREWS (F)
RETAINING
RING (C)
STEP 6
CAP
NUTS (E)
*NOT INCLUDED