Sea Gull Lighting 44852-965 Installation Guide

HC-1288
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
BEFORE YOU BEGIN
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
012208
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don't need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Place backplate (C) against wall and mark location for dry wall
anchors. Drill appropriate sized holes in drywall and insert anchors.
STEP 2:
Pull supply wires through appropriate opening in backplate (C). Place
backplate (C) against wall and secure by installing drywall screws (not
supplied) into drywall anchors. Install outlet box screws (not supplied)
into outlet box through appropriate openings in back plate (C) when
applicable.
*GROUND
WIRE
GREEN
GROUNDING
SCREW (G)
BACKPLATE (C)
CANOPY (I)
CAP NUTS (E)
DRYWALL
ANCHOR
MOUNTING
STUDS (F)
RETAINING
RING (H)
FIGURE 1
SOCKET
CUP (B)
SHADE (A)
*NOT INCLUDED
INSTALLATION (continued)
HC-1288
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according to
the directions below:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (D). Wrap the ground wire from the fixture (if supplied) and
the ground wire from the outlet box (bare metal or green insulated
wire) around the green grounding screw (G) on the universal
mounting bar (D) if uninsulated wire is on the universal mounting
bar (D), connect the ground wire from the fixture (if supplied) and
the outlet box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 1:
Make sure no bare wires can be seen outside wire connectors. Push
the fixture firmly over the mounting studs (F) and against the
backplate (C). Secure canopy (I) in place by threading cap nuts (E)
onto mounting studs (F).
GROUP A:
CONNECT TO BLACK HOUSE WIRE
GROUP B:
CONNECT TO WHITE HOUSE WIRE
BLACK
WHITE
STEP 2:
Place shade (A) on socket cup (B) and secure by threading retaining
ring (H) onto socket.
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
STEP 3:
Install lamps.
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.