Hampton Bay 19574-011 Installation Guide

TROUBLESHOOTING:
Bulb will not light.
Fuse blows or circuit
breaker trips when light
is turned on.
Possible Cause
Corrective Action
1. Bulb is burned out.
1. Replace light bulb.
2. Power is off.
2. Make sure power supply
is on.
3. Faulty wire connection.
3. Check wiring.
Crossed wires or power
wire is grounding out.
Check wire connections.
INSTRUCTION MANUAL
Interior Decorative Lighting
Home Depot SKU (724-245) UPC (773546211932)
PRODUCT MAINTENANCE:
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use
clean water, never a solvent) to wipe the shade and surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning
off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or
slightly dampened clean cloth (use clean water, never a solvent) to wipe the inside
shade and interior surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry
soft cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship
for a period of five (5) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the
manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident,
modifications, alterations, neglect or mishandling. This warranty shall not apply to any product that is
found to have been improperly installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident,
misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material
or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface
and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and
specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other
than the warranty contained herein. The manufacturer specifically disclaims any liability and shall
not be liable for any consequential or incidental loss or damage, including but not limited to any labor
expense costs involved in the replacement or repair of said product.
Page 6
Page 1
Thank you for purchasing this Hampton Bay interior decorative lighting. This product
has been manufactured with the highest standards of safety and quality.
FEATURES:
A satin nickel finish with elegant white glass makes this expressive sconce a welcome
addition to the home.
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer Service
Team at 1-877-527-0313 or visit www.homedepot.com. Please reference your
SKU# (724-245) UPC# (773546211932).
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION
(not included):
Gloves
Wire Strippers
Wire Cutters
Ladder
Flathead
Screwdriver
Phillips
Screwdriver
Electrical Tape
B10 60W Bulb
(not included)
ADDITIONAL PARTS (included):
CAUTION:
1. Before starting installation of this fixture or removal of a previous fixture, disconnect
the power by turning off the circuit breaker or by removing the fuse at the fuse
box.
1. Finishing Screw
2. Glass Shade
3.Rubber Gasket
4. Bracket
5. Junction Box
Screws (x2)
6. Screws (x2)
7. Wire Connectors
(x3)
8. Universal
Cross Bar
9. Decorative Caps
(x2)
10. Finial
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL
QUESTIONS.
3. If you have any non-electrical questions about this fixture, please contact our
Customer Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU# (724-245) UPC# (773546211932).
4. Keep your receipt and these Instructions for Proof of Purchase.
Page 2
Page 3
ASSEMBLY INSTRUCTIONS:
1. Carefully unpack the fixture; lay out all parts on a clean surface.
ASSEMBLY:
2. Firmly attach the Screws (6) to the Universal Cross Bar (8) with their heads facing
opposite to the Ground Screw, matching with the spacing between mounting holes
of the Canopy.
1. Finishing Screw
3. Firmly attach the Universal Cross Bar (8) to the Junction Box using the Junction
Box Screws (5); ensure that the head of the Ground Screw faces out.
2. Glass Shade
4. Rigidly connect the white wires from the Canopy and the Junction Box (drawn
through the central hole of the Universal Cross Bar) using a Wire Connector (7);
reinforce this connection by wrapping Electrical Tape around this junction.
5. Repeat Step 4 above for the black wires coming from the Canopy and the Junction
Box (drawn through the central hole of the Universal Cross Bar).
3.Rubber Gasket
6. Repeat Step 4 above for the grounding wires coming from the Canopy and the
Junc¬tion Box (drawn through the central hole of the Universal Cross Bar (8); alternately, connect them to the Ground Screw of the Universal Cross Bar (8).
B10 Bulb 60W
Max. (not included)
4. Bracket
Note: If you have questions that are electrical in nature, consult your local electrical
code or a qualified electrician for approved grounding methods.
Canopy
7. Push all electrical wires and connections into the Junction Box (through the central
hole of the Universal Cross Bar); ensure that they are not damaged.
8. Push the Canopy to align its mounting holes with the Screws (6) of the Universal
Cross Bar (8) and attach it firmly flush with the wall using the Decorative Caps (9).
9. Firmly attach the Finial (10) to the bottom of the Frame (part of Canopy).
10. Locate the Bracket (4) over the Socket (part of Frame)
11. Install the Light Bulb (Type: B10, 60 Watts max, not included) into the Socket
(part of Frame).
12. Place the Glass Shade (2) and rubber gasket (3) in place over the Bracket (4) and
attach it firmly in place using the Finishing Screw (1).
13. Turn ON the power at the circuit breaker or fuse box. Operate the light switch, to
turn the fixture ON and OFF.
Page 4
Socket
(Part of Frame)
5. Junction Box Screws (x2)
Ground Screw
6. Screws (x2)
Frame
(Part of Canopy)
Junction Box
7. Wire Connectors (x3)
8. Universal Cross Bar
10. Finial
9. Decorative Caps (x2)
Page 5