Hampton Bay 17100 Installation Guide

INSTRUCTION MANUAL
1 Light Track Pendant in Brushed Nickel Finish
Home Depot SKU 720-879 (UPC 718212171004)
(Brushed Nickel fixture)
Track Construction:
Hardwire Construction:
LA-1599E/S/F
Page 1
Thank you for purchasing this Hampton Bay Track Lighting. This product
has been manufactured with the highest standards of safety and quality.
FEATURES:
1. Traditional 1 Light Track Pendant in Brushed Nickel Finish.
2. Install as a Hardwire Mini Pendant or Track Pendant.
3. Easy to assemble and install.
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer
Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU (720-879 Brushed Nickel fixture) or UPC
(718212171004 Brushed Nickel fixture).
Page 2
CAUTION:
1. Before starting installation of this fixture or removal of a previous
fixture, disconnect the power by turning off the circuit breaker or by
removing the fuse at the fuse box.
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY
ELECTRICAL QUESTIONS.
3. If you have any non-electrical questions about this fixture, please
contact our Customer Service Team at 1-877-527-0313 or visit
www.homedepot.com. Please reference your SKU (720-879 Brushed
Nickel fixture) or UPC (718212171004 Brushed Nickel fixture).
4. Keep your receipt and these Instructions for Proof of Purchase.
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION
(not included):
Light Bulb
(60 watt maximum)
Safety goggles
Flathead screwdriver
Phillips screwdriver
Step Ladder
Electrical tape
Wire strippers
Wire cutters
Page 3
PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
1 Canopy (#7)
3 Screw (#20)
1 Shade (#5)
PARTS INCLUDED FOR INSTALLATION (parts are not to scale):
1 Crossbar (#11)
2 Mounting Screw (#8)
2 Out Box Screw (#10)
1 Ground Screw (#12)
3 Wire Connector (#14)
INSTALLATION INSTRUCTIONS:
Track Construction:
1. Secure the Metal Tube (#4) to top of Socket Cup (#19).
2. Align the holes on the Shade (#5) and Socket Cup (#19), secure them with Screws
(#20).
3. Please follow these instructions if you need to adjust the length of the wire before
installation:
a. Begin by determining the length of wire needed for proper hanging height. Use a
wire cutter to discard un-wanted wire. (Note: keep 2” additional length of wire
for wire connection.) Carefully cut and remove approximately 2” of the outer
sheathing from cord end and strip 3/8” of the wire ends bare to expose the copper
strands. (CAUTION: Be careful not to cut or damage the insulation on the inside
wires when removing the outer insulation).
b. Loosen the Screw (#15) at the top of adapter using a screwdriver, then take out
the connector assembly (#16), Wire Connectors (#17), Wire Grip (#18) and pass
through the Wire (#3) from the inside of the adapter (#2) as shown in Fig. 1.
c. Make wire connections.
15. Screw
16. Connector Assy
16. Connector Assemble
17. Wire Connector
18. Wire Grip
3. Wire
2. Adapter
4. Metal Tube
19. Socket Cup
5. Shade
Fig.1
Page 4
Track Construction: Cont’
When installing or using this track system,
basic safety precautions should always be
followed, including the following:
a.) Read all instructions.
b.) Do not install this track in damp or wet
locations.
c.) (For track lighting systems other than those
that comply with Section 31, Field Cutting)
Do not cut any track sections.
d.) Do not install any part of a track system less
than 7 feet above the floor.
e.) Do not install any luminaire assembly
closer than 6 inches from any curtain, or
similar combustible material.
f.) Disconnect electrical power before adding
to or changing the configuration of the
track.
g.) Do not attempt to energize anything other
than lighting track luminaires on the track.
To reduce the risk of fire and electric shock,
do not attempt to connect power tools,
extension cords, appliances, on like items to
the track
h.) For installation with HAMPTON BAY EC
series track only.
When the adapter is secured and ready for
install:
1. Hold down the Lock Lever; turn Adapter
(#2) in a clockwise direction to Track (#1).
Twist ground side of connector towards
ground side of track until connector snaps
into place. Release Lock Lever.
2. Install the proper Light bulb (not included)
in
accordance
with
the
fixture’s
specifications. (DO NOT EXCEED THE
MAXIMUM WATTAGE RATING).
Installation is complete. Turn on the power at
the circuit breaker or fuse box. Turn the light
switch on to activate the fixture.
Notice:
1. Connector is designed to lock into
track section by turning connector in
one direction only.
2. Turn Ground indicator tab towards
the ground groove on track to align
ground tab with ground conductor.
1. Track
2. Adapter
3. Wire
Lock Lever
Push down and
twist to remove
from track
19. Socket Cup
20. Screw
5. Shade
6. Bulb
Page 5
Hardwire Installation Instructions:
1. Secure the Metal Tube (#4) to top of Socket
Cup (#19).
2. Align the holes on the Shade (#5) and Socket
Cup (#19), secure them with Screws (#20).
3. Determine the length of wire needed for
proper hanging height. Use a wire cutter to
discard un-wanted wire.
(Note: keep 2”
additional length of wire for wire connection.)
Carefully cut and remove approximately 2” of
the outer sheathing from cord end and strip
3/8” of the wire ends bare to expose the copper
strands. (CAUTION: Be careful not to cut or
damage the insulation on the inside wires when
removing the outer insulation).
4. Place the Wire (#3) through the Canopy (#7)
and secure with Set Screw (#9). (Note:
Maintain the proper length of wire for wire
connects.)
5. Attach the Crossbar (#11) to the Outlet Box
(#13) with Outlet Box Screws (#10). The side
of the Crossbar marked “GND” must face out.
6. Connect the white wire from the fixture to the
white wire from the outlet box (#13) and the
black wire from the fixture to the black wire
from the outlet box (#13). Cover the two wire
connections using the two provided wire
connectors (large) (#14). Wrap the two wire
connections with electrical tape for a more
secure connection. If your outlet box has a
ground wire (green or bare copper), connect
fixture’s ground wire to it using the wire
connector (large) (#14). Otherwise connect the
ground wire from the fixture to Ground screw
(#12) on the Crossbar (#11). Note: If you have
electrical questions, consult your local
electrical code for approved grounding
methods.
7. Tuck these wire connections neatly into the
ceiling outlet box and then raise the canopy all
the way to the ceiling. Secure the Canopy (#7)
against the ceiling with Mounting Screws (#8).
8. Install the light bulb (not included) in
accordance with the fixture’s specifications.
(DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!!)
Installation is complete. Turn on the power at the
circuit breaker or fuse box. Turn the light switch
on to activate the fixture.
7. Canopy
9. Set Screw
3. Wire
4. Metal Tube
19. Socket Cup
20. Screw
5. Shade
6. Bulb
Black wire
White wire
14.Wire connector
(Large)
12.Ground Screw
7. Canopy
13. Outlet box
Ground wire
11. Crossbar
10. Outlet Box
Screw
8. Mounting
Screw
9. Set Screw
Page 6
TROUBLESHOOTING:
Bulb will not light.
Fuse blows or circuit
breaker trips when light
is turned on.
Possible Cause
1. Bulb is burned out.
2. Power is off.
Corrective Action
1. Replace light bulb.
2. Make sure power
supply is on.
3. Faulty wire connection.
3. Check wiring.
4. Faulty switch.
4. Test or replace switch.
Crossed wires or power wire Check wire connections.
is grounding out.
PRODUCT MAINTENANCE:
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use
clean water, never a solvent) to wipe the shade and surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning off
the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly
dampened clean cloth (use clean water, never a solvent) to wipe the inside of the shade
and exterior surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry
soft cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a
period of five (5) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the
manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident,
modifications, alterations, neglect or mishandling. This warranty shall not apply to any product that is found
to have been improperly installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident,
misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material
or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface
and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specially disclaims any warranty, whether express or implied,
of fitness for a particular purpose, other than the warranty contained herein. The manufacturer
specifically disclaims any liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor / expense costs involved in the replacement or repair of
said product.
Page 7