the great outdoors by Minka Lavery 73102-143C-L Instructions / Assembly

INSTALLATION INSTRUCTIONS
For Model 73101/73102/73103-143C-L
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
HANGING THE FIXTURE (Fig. 1)
1. Shut off the power at the circuit breaker and remove the old
fixture, including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on a
clear area. Take care not to lose any small parts necessary for
installation.
3. Thread the 2 mounting screws (B) into the mounting plate (C)
(part #:A-020) spaced the same distance apart as the holes in
the fixture back plate (E). (You can adjust the length of the
screws if necessary.)
4. Attach the mounting plate (C) to the outlet box (A) (not
supplied) with outlet box screws (D). (Size: #8-32*1/2L).
Note: this side of mounting plate marked “GND” must face out.
5. Attach the small glass (H) and the big glass (I) into the fixture
frame (F) with glass clips (G).
CONNECTING THE WIRES (Fig. 2)
6. Connect the electrical wires as shown in Fig.2.Making sure
that all wire connectors are secured. If your outlet box has a
ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the circular strap using the green screw provided.
COMPLETING THE INSTALLATION (Fig.1)
7. Align the fixture back plate (E) to mounting plate (C) and
secure with the gasket (J) and cap nuts (K).
8. To prevent moisture entering the outlet box and causing a
short, use clear caulking (i.e. Indoor/Outdoor Silicone Sealant)
to outline the outside of fixture back plate where it meets the
wall leaving a space at bottom to allow moisture a means to
escape. (Fig. 3)
8. Bulb information: (1 x AC LED 10W included.)
DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
(NE PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
Fig. 1
Fig. 2
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or
Bare
Copper(G
round)
Fig. 3
Replacing LED module (Fig. 4)
The LED module can be replaced by a qualified electrician and
shut off the power at the circuit breaker and remove fixture from
the outlet box without cutting of wire and without damage to any
decorative element to which the fixture is attached. See
installation steps for more details (Fig 4.)
a. Remove the metal sheet (J) by loosening screws (K).
Carefully disconnect the wire covers.
b. Remove screws (Q) to disassemble the module cover (P),
glass (O), module ring (N), LED module (M).
c. Carefully remove the LED module (M) for re-lamping.
d. Note: The LED module should be provided by a specified
supplier.
e. For better heat dissipation the LED module (M) should be
installed with the heat transfer material (L) when re-lamping
Your installation is now complete. Return power to the
junction box and test the fixture
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
Caulking
Back plate
Fig. 4
M
L
J
K
N
O
P
Q