the great outdoors by Minka Lavery 72501-615B-L Instructions / Assembly

INSTALLATION INSTRUCTIONS
For Model
:72501-L
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
HANGING THE FIXTURE (Fig. 1)
1. Shut off the power at the circuit breaker and remove the old
fixture, including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on a
clear area. Take care not to lose any small parts necessary for
installation.
3. Thread the 2 mounting screws (C) into the mounting plate (D)
(part #:A-020) spaced the same distance apart as the holes in
the fixture back plate (F). The length of screws (C) into
mounting plate (D) may be adjusted if necessary.
4. Attach the mounting plate (D) to the outlet box (A) (not
supplied) with outlet box screws (E). (Size: #8-32*1/2L).
Note: The side of mounting plate marked “GND” must face
out.
CONNECTING THE WIRES (Fig. 2)
5.Connect the electrical wires as shown in Fig.2.Making sure
that all wire connectors(B) are secured. If your outlet box has a
ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the circular strap using the green screw provided.
COMPLETING THE INSTALLATION (Fig.1)
6. Align the fixture body to mounting plate (D) and secure with
Rubber washers (G) and cap nuts (H).
7. To prevent moisture entering the outlet box and causing a
short, use clear caulking (i.e. Indoor/Outdoor Silicone Sealant)
to outline the outside of fixture back plate where it meets the
wall leaving a space at bottom to allow moisture a means to
escape. (Fig. 3)
8. Bulb information: (1 x AC LED 10W included.)
DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
(NE PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
B
F
A
C
E
H
Fig. 2
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black
(Hot)
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or
Bare
Copper(G
round)
Fig. 3
Caulking
Replacing LED module (Fig. 4)
The LED module can be replaced by a qualified electrician
without cutting of wire and without damage to any decorative
element to which the fixture is attached. See installation steps for
more details (Fig 4.) Shut off power at the circuit breaker and
remove the fixture from the wall.
a. Remove the metal cover (S) by unscrewing from the fixture
body (I), and then loosen screws (M) to remove the metal
cup (K). Carefully pull out the wires (J) and disconnect the
LED module from the fixture.
b. Remove the module cover (Q), glass (P), module ring (O),
the LED module (N) by loosening screws (R).
c. Carefully remove the LED module (N) for re-lamping. Note:
The LED module should be provided by a specified supplier.
d. For better heat dissipation the LED module (N) should be
installed with the heat transfer material (L) when re-lamping
Your installation is now complete. Return power to the
junction box and test the fixture
Set #:A-020
Circular strap(1)
Grounding screw(1)
Mounting screw(2)
Back plate
Fig. 4
I
J
K
M
N
P
R
L
O
Q
S