the great outdoors by Minka Lavery 8101-A138-L Instructions / Assembly

INSTALLATION INSTRUCTION
Item#8101/8102-A138-L (New. 05/02/2013)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig. 1)
Fig. 1
1. Shut off power at the fuse box or circuit breaker box. If
necessary, remove the old fixture including the mounting
hardware.
2. Carefully unpack your new fixture and lay out all the parts
on a clear area. Take care not to lose any small parts
necessary for installation.
3. Thread mounting screws (C) into the pre-drilled holes in
the circular strap (A) spaced the same distance apart as
the holes in the back plate and secure with hex nut (F).
4. Attach the circular strap (A) to the junction box with
mounting screws (B) (Size: #8-32N*L0.5”). The side of the
circular strap marked “GND” must face out.
E
C
B
D
H
Fig. 2
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
COMPLETING THE INSTALLATION
6. Align back plate (D) to screws (C) and secure with cap
nuts (E).
7. To prevent moisture from entering the outlet box and
causing a short, use clear caulking (i.e. Indoor/Outdoor
Silicone Sealant) to outline the outside of fixture back-plate
where it meets the wall leaving a space at bottom to allow
moisture a means to escape (Fig.3).
8. Bulb (G) information: (1 X AC LED 10W included). (DO
NOT EXCEED THE SPECIFIED WATTAGE!) (NE PAS
DEPASSER
LA
PUISSANCE
NOMINALE
MAXIMALE!).
HOUSE
WIRES
Black
(Hot)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green
(Ground)
Fig. 3
CAULKING
REPLACING LED MODULE (Fig.4)
The LED module can be replaced by a qualified electrician
without cutting of wire and without damage to any decorative
element to which the fixture is attached. See installation
steps for more details (Fig.4)
a. Shut off the power, use a screw driver to loosen the
screws (Q) and remove the glass shield (P) from the
aluminum cover (T).
b. Loosen the module screws (O) and remove the LED
module (L) and glass (M) from the white plastic ring (N).
c. Loosen screws (J) to remove aluminum plate (I) and
aluminum cover (T) from the bracket (S).
d. Remove wire connectors (R) to disconnect the LED for
re-lamping. (Note: The LED module should be provided
by specified supplier.)
e. For better heat dissipation the LED module (L) should be
installed with the heat transfer material (K) when
re-lamping.
A
Set# A-022
-Circular Strap
-Ground Screw
-Mounting Screw*2
G
CONNECTING THE WIRES (Fig. 2)
5. Connect the fixture wires to the junction box wires as
shown in Fig.2 making sure all wire connectors are
secured. If the junction box has a ground wire (green or
bare copper) connect the fixture’s ground wire to it,
otherwise connect the fixture’s ground wire directly to the
circular strap with the green screw provided.
F
BACKPLATE
Fig. 4
S
K
M
N
T
I
J
R
L
O
P
Your installation is now complete. Return the power to the
junction box and test the fixture.
Q
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-2271E