the great outdoors by Minka Lavery 72427-212 Instructions / Assembly

INSTALLATION INSTRUCTIONS
For Model 72427-212 (Rev. 03/07/2014)
READ AND SAVE THESE INSTRUCTIONS
WARNING !
S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARING FOR INSTALLATION (Fig. 1)
1. Shut off the power at the circuit breaker and remove the old
fixture, including the mounting hardware.
2. Carefully remove the fixture from the carton and check that all
parts are included as shown in the illustration.
3. Attach the circular strap (A) to the outlet box using the mounting
screws (B) (Size: #8-32N*L0.5”). The side of the circular strap (A)
marked “GND” must face out.
4. Install 2 studs (C) into the circular strap (A), spaced the same
distance apart as the holes in back plate (D).
5. The support cable is provided to support the weight of the fixture
while wiring. Align the fixture to circular strap (D) and attach hook
(K) on the end of support cable (J) into a slot located on circular
strap (D). Carefully allow the support cable (J) to support the
weight of the fixture while wiring. (Fig 1)
Fig.1
Set# A-020-2
- Circular strap
- Ground Screw
- Mounting Screw*2
A
B
K
C
J
G
CONNECTING THE WIRES (Fig. 2)
D
6. At this point, connect the electrical wires as shown in figure 2,
making sure that all wire connectors are secured. If your outlet
has a ground wire (green or bare copper), connect the ground
wire from the fixture to it. Otherwise, connect the ground wire from
the fixture directly to the circular strap and secure with the green
screw provided. After wires are connected, tuck them carefully into
the outlet box.
E
I
F
H
COMPLETING THE INSTALLATION (Fig. 1)
7. Align back plate (D) onto studs (C) and secure with cap nuts (E).
8. To prevent moisture from entering the outlet box and causing a
shortage, use clear caulking (i.e. Indoor/Outdoor silicone sealant)
to outline the outside of fixture back plate where it meets the wall
leaving a space at the bottom to allow moisture a means to
escape (Fig.3).
9. Pull up latch (F) and open the door.
10. Place the plastic covers (included in mounting hardware bag) over
the glass holder clips.
11. Install glass (H) using the glass clips on frame (G). Note: The rear
glass must be installed first, followed by the side glass. The front
glass should be installed last.
12. Install 4*60W B10.5 bulb (s) (not included) in accordance with the
fixture’s specification. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!).
13. When replacing the glass (H), pull up latch (F) and open the door.
Loosen the clips and remove glass (H). Note: The side glass must
be removed before the rear glass. After replacing the glass, repeat
step 9, and then close the door.
14. For installing or replacing bulbs at a later date, pull up the latch (F)
and open the door. (Fig.1)
Your installation is now complete. Return power to the outlet box and
Fig.2
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or
Bare
Copper(Gr
ound)
Fig.3
Backplate
test the fixture.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-2396E
CAULKING