the great outdoors by Minka Lavery 72424-212 Instructions / Assembly

INSTALLATION INSTRUCTIONS
For Model 72424-212 (Rev. 06/19/2013)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARING FOR INSTALLATION (Fig. 2)
1. Shut off the power at the fuse box or circuit breaker box
and remove the old fixture from the ceiling, including the
mounting hardware.
2. Carefully unpack your new fixture and lay out all the
parts in a clear area. Take care not to misplace any small
parts necessary for installation.
3. Thread the nipple into the ceiling loop until snug.
4. Thread the other end of the nipple into the crossbar until
snug. Note: The length of the nipple into the crossbar
may be adjusted if necessary.
5. Use the lock washer and hex nut to secure the nipple
into the crossbar.
6. Take this crossbar assembly and mount it to ceiling
outlet box with mounting screws (Size: #8-32N*L0.5”).
The side of crossbar marked with “GND” must face out.
7. Determine the desired hanging height and use a pair of
proper chain pliers to remove and discard the excess
chain.
8. Open one end of chain and attach it to the fixture ceiling
loop and close the chain. Slip the canopy and lock collar
over the chain and allow them to rest on the fixture body.
Open the other end of the chain and attach it to chain
loop and close the chain.
9. Carefully lace the fixture’s wires through the chain. Feed
the fixture wires through the loop and nipple assembly.
CONNECT THE WIRES (Fig. 3)
10. Connect the electrical wires as shown in Fig. 3, making
sure that all wire connectors are secured. If your outlet
box has a ground wire (green or bare copper), connect
the fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the crossbar using the
green screw provided.
11. Tuck these wire connections neatly into the ceiling outlet
box and then raise the canopy all the way to the ceiling.
Raise the lock collar and thread onto ceiling loop
protruding through canopy (Fig.2).
COMPLETING THE INSTALLATION (Fig. 1)
12. Pull up the latch (A) and open the door.
13. Install 3*60W B10.5 bulb(s) (not included) in accordance
with the fixture’s specification. (DO NOT EXCEED THE
MAXIMUM WATTAGE RATING)(NE PAS DEPASSER
LA PUISSANCE NOMINALE MAXIMALE!).
14. When replacing the glass (B), pull up the latch (A) and
open the door. Loosen the clips and remove glass (B).
After replacing the glass, re-tighten the glass clips, and
then close the door.
15. For installing or replacing bulbs at a later date, pull up
the latch (A) and open the door. (Fig.1)
Your installation is now complete. Return power to the junction box
and test the fixture.
Fig.1
Set# A-010
- Crossbar
- Ground screw
- Mounting Screw*2
A
B
Fig.2
Outlet Box
Hex Nut
Crossbar
Lock Washer
Mounting Screw
Nipple
Ceiling Loop
Chain
Canopy
Lock Collar
Chain#HCH2072-212
Wire
Loop
Fig. 3
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black
(Hot)
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-2328E
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green
(Ground)