Hunter 27183 Instructions / Assembly

Quiet Fan Control with Light Dimmer
Ratings: 120 VAC, 1.6 A, 60 Hz
4-Speed Fan and Light Dimmer Slide
Preset Control – Model 27183
Read and save these instructions.
Caution:
Risk of Electrical Shock!
All wiring must be performed in accordance with
national and local electrical codes. To avoid
overheating and possible damage to other
equipment, do not install to control a receptacle,
fluorescent light fixture, motor operated appliance, or transformer-supplied appliance. Use
only to control one paddle-blade ceiling fan and
incandescent light fixture.
Notes:
1. For use only with electrically
reversible ceiling fans rated at 1.6 A or
less, and fan light kits rated at 300
watts total or less. Not for use with any
other lighting fixtures or electrical appliances.
2. Not for use with shaded-pole or nonreversible motors. Not recommended for
use with the Hunter Original.® For
Hunter Original® series fans, use Hunter
control model numbers 22691, 26591,
or 22798.
3. This control requires separate wiring
for the ceiling fan and fan light kit. If
one wall switch currently supplies power
to both the fan and light, additional
wiring for the light fixture will be
required to use this All-Fan™ control.
4. MEDIUM and both LOW speeds may
vary from the ceiling fan’s factory-set
speeds because of motor variations.
3. Disconnect power to the ceiling fan and light at the
main electric panel. Remove fuse, or switch circuit breaker
to the OFF position.
4. Refer to the Installation Figure for your All-Fan™ speed
control. Remove wallplate to expose the wiring. Identify
the wires supplying power to the ceiling fan and fan light
kit. Install in a metal or plastic wallbox.
5. Disconnect the existing switch(s) and remove from the
switch box.
6. Use the wire nuts supplied to make the ceiling fan and
fan light kit connections as shown in the Wiring Diagram.
If a ground wire is provided in your electrical box, attach
it to the ground screw near the bottom of the mounting
plate.
7. Gently push wires and speed control into wall box.
Attach the All-Fan™ control to the
switch box with the two screws
supplied.
8. Mount wallplate over control with
existing screws.
9. Move both sliders to the OFF
position.
10. Restore power at main electrical
panel.
11. Operate ceiling fan by moving the
fan speed slider to the desired speed.
Dim the light fixture by raising the light
dimmer slider to the desired light level.
The fan and light are turned Off at the
bottom position. The preset switch
beneath the sliders may be used to turn
both fan and light ON or OFF at a preset
level.
For best fan operation: select HIGH
speed until motor starts, then select
desired speed.
Installation Instructions:
1. Set the ceiling fan’s speed to the HIGH position before
installation. Do not change the ceiling fan‘s speed setting
after your speed control is installed, as damage to your
ceiling fan or All-Fan™ control may result.
2. Verify proper operation of the ceiling fan and fan light
kit wall switches before installation. Improper wiring can
damage the control, and will void the warranty.
Lea y guarde estas instrucciones
Cuidado: ! Riesgo de choque eléctrico
Todo el cableado y conexiones se deben hacer de
acuerdo con los códigos eléctricos nacionales y
locales.
Notas:
1. Para uso solamente con ventiladores de cielo raso eléctricamente reversibles de capacidades de 1,6 A o menores y conjuntos de luces para ventilador con una capacidad total de 300
watts o menor. No se debe usar con ninguna otra
lámpara ni aparato eléctrico.
2. Este control requiere circuitos separados para el ventilador de
cielo raso y el conjunto de luces. Si el mismo interruptor de pared
suministra actualmente la energía, tanto para el ventilador como
para las luces, se necesitará instalar un circuito
separado para el conjunto de luces.
Instrucciones de instalación:
1. Coloque el control de velocidad del ventilador
de cielo raso en la posición de Alta Velocidad
antes de instalar este control. No cambie el
ajuste de velocidad de su ventilador de cielo
luego de tener instalado el control de velocidad,
puesto que podría dañar su ventilador de cielo o
el control All-Fan.™
2. Verifique que los interruptores de pared del
ventilador de cielo raso y del conjunto de luces
trabajen correctamente antes de la instalación.
Las conexiones incorrectas pueden dañar el control y anularán la
garantía.
3. Desconecte la energÌa eléctrica del ventilador
de cielo raso en el panel eléctrico principal.
Retire el fusible o coloque el disyuntor en la
posición “OFF” (apagado).
4. Vea la ilustración que muestra la instalación
de su control de velocidad All-Fan.™ Retire la
placa de la pared para exponer los cables.
Identifique los alambres que suministran
energía al ventilador y al conjunto de luces.
5. Desconecte el(los) interruptor(es) existente(s) y retÌrelo(s) de la
caja.
Black
Hot
Ventilador de 4 velocidades / Control para
oscurecer la luz
Blue
Fan
Red
6. Use las tuercas de alambre suministradas para hacer las
conexiones como se muestran en el Diagrama de Conexiones.
Si su caja eléctrica contiene un alambre de tierra, conéctelo al
tornillo di tierra ubicado cerca de la placa de montaje inferior.
120VAC
60Hz
Light
Neutral
Wiring Diagram
7. Empuje los alambres y el control de velocidad con mucho
cuidado dentro de la caja del interruptor. Asegure el control a la
caja del interruptor con los dos tornillos suministrados.
8. Monte la placa de la pared sobre el control con los tornillos
existentes.
9. Mueva las dos palancas deslizables a la posición “OFF” (apagada).
10. Vuelva a conectar la energía eléctrica en el panel eléctrico
principal.
11. Haga funcionar el ventilador de cielo raso moviendo la
palanca deslizable a la velocidad deseada. Haga oscurecer la luz
deslizando la palanca del control de luz al nivel de iluminación
deseado. El ventilador y las luces están apagados (OFF) en la
posición inferior del control. Se usa un interruptor preajustado
para encender y apagar, tanto el ventilador como las luces, a un
nivel predeterminado.
Para la mejor operación del ventilador: seleccione
Alta Velocidad hasta que el motor arranque y
entonces seleccione la velocidad deseada.
HUNTER FAN COMPANY ALL-FAN™
CONTROL LIMITED WARRANTY
The Hunter Fan Company makes the following limited warranty
to the original purchaser of the ALL-FAN™ Control (“Control”):
Your Control is warranted to be free from
defects in material and workmanship for a
period of one year from the date of sale. If the
Control malfunctions or fails within the warranty
period due to a defect in material or workmanship we will replace it free of charge. IF THE
ORIGINAL PURCHASER CEASES TO OWN THE
CONTROL, THIS WARRANTY AND ANY
IMPLIED WARRANTY, INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS
WARRANTIES. THE DURATION OF ANY
IMPLIED WARRANTY, INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IN RESPECT TO ANY CONTROL, IS EXPRESSLY LIMITED TO THE PERIOD
OF THE EXPRESS WARRANTY SET FORTH
ABOVE FOR SUCH CONTROL. This warranty
excludes malfunctions or failures which were
caused by repairs by persons not authorized by
us, mishandling, improper installation, modifications, or damage to the Control while in your
possession, or unreasonable use. This warranty
does not apply to batteries or to deterioration or
damage to the product caused by the use of
faulty batteries. To obtain a replacement, return your Control
postage prepaid along with proof of purchase to Hunter Fan
Company Service Department at 2500 Frisco Avenue, Memphis,
Tennessee 38114. IN NO EVENT SHALL HUNTER FAN COMPANY
BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE
ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
Form 41314 (6/98)