Hunter 99120 Instructions / Assembly

www.HunterFan.com
1.888.830.1326
To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off
the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers
in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
Universal Wall
Mount Control
Model #99120
Getting Started
For low profile fans, the receiver should
be secured to the ceiling bracket with a
cable tie.
Receiver
Receiver
OR
n
Tur
er
Pow
OFF
Canopy
Remove the canopy. If uncertain how
to remove it, reference the fan’s owner’s
manual. With wiring exposed, it may be
helpful to note existing wire connections
or take a digital photo for reference.
Remove the wire connectors that connect
the wires from the outlet box to the fan,
leaving the grounding wires connected.
RECEIVE
R
OR
Ceiling
Bracket
Receiver
Fan Body
Canopy
Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8” remaining. Re-strip the fan lead wires 1/2”. Place remaining excess wire into
the ceiling electrical box. The bracket and fan must remain properly grounded.
You may have installation issues if the fan is installed on an angled ceiling. For assistance, call 1-888-830-1326.
Wiring the Wall Control
OM CEILING
FR
black (live in)
FR
white (neutral in)
blue
black
white
If you are uncertain about
wire colors or connections,
please contact a qualified
electrician.
CONNECT WIRES FROM
RECEIVER TO WIRES FROM
OUTLET BOX - Using an
orange wire connector,
connect the black wire
(ungrounded) from the
ceiling to the black wire from
the receiver (marked “live
in”). Connect the white wire
(grounded) from the ceiling
to the white wire from the
receiver (marked “neutral in”).
black (ungrounded)
CONNECT WIRES FROM
RECEIVER TO FAN - Using
the blue wire connectors,
connect the white wire
from the receiver (marked
“common out”) to the white
wire from fan. Connect the
black wire from the receiver
(marked “fan out”) to the
black wire from the fan.
Connect the blue wire from
the receiver (marked ”light
out”) to the blue wire (or
possibly black with white
stripe) from the fan.
white (grounded)
blue (light out)
black (fan out)
white (common out)
M FA N
OR
Receiver
Choose the hanging system that most closely resembles the one used by your fan and install the receiver as shown and wire as directed.
Wiring the Receiver
FRO
Cable Tie
Canopy
Before installing the Universal
Remote Control Receiver,
use the pull chains to set the
fan speed to HIGH and the
light to ON. Be sure power is
OFF before proceeding with
installation.
OM
FR
Ceiling
Plate
OM
RECEIV
AFTER ALL WIRES ARE
CONNECTED and secured
with wire connectors,
re-install the canopy.
After removing the switch plate
cover, remove all wiring from
the switch.
Using orange wire connectors,
connect the two black wires
(ungrounded) from the outlet
box. Also connect the two green
or bare wires (grounding) from
the outlet box with the grounding
wire from the wall control.
Insert the wall control into
the outlet box and secure the
two screws using a Phillips
head screwdriver.
Install the cover plate using a
Phillips Head screwdriver to
secure the two cover plate screws.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
ER
M0061-01 • 07/26/13 • © Hunter Fan Company
www.HunterFan.com
Pairing
Maintenance
1.888.830.1326
Operations
Light
Battery
Holder
High
Medium
Battery
er
ow
P
rn
Tu
Battery
Door
Before operating the wall control,
press the battery door to eject it.
Using a Phillips head screwdriver,
remove the battery holder. Install
the battery with the positive (+) side
facing downward. Secure the battery
by reinstalling the battery holder.
Finally, reinstall the battery door into
the wall control. When necessary,
replace with CR2032 battery.
ON
Use the pull-chain switch on the
fan to set the fan speed to the HIGH
position before operation.
Troubleshooting
The Safe-Exit Program gives
you about thirty seconds of
light when you turn the lights
off to exit the room before the
lights go out. To use Safe-Exit:
Fan will not start
• Make sure the power is on at the
circuit breaker and the wall switch.
• Make sure the battery is working.
• Make sure that the transmitter
and receiver are paired.
• Check wire connections inside of
the canopy.
• The lights will flash for visual
confirmation.
• The lights will stay on 50%
brightness for 15 seconds and
then begin to dim. After a total
of 30 seconds, the lights will be
completely off.
Note: For CFL lighting, the lights
will stay on 100% brightness
for 30 seconds. After a total of
30 seconds, the lights will be
completely off.
Fan Off
Fan
Off
Note: The remote must be paired
IMPORTANT
Safe-Exit
• Press the Fan Off button for at
least three seconds to initiate the
Safe-Exit Mode.
Low
High
Remote control of fan is erratic
• Make sure the battery is installed
correctly.
• Install a fresh battery.
Lights do not dim
• Check to see if a CFL bulb is
installed. The control has a feature
that automatically detects CFL
bulbs and turns off dimming if a
CFL bulb is installed.
CFL bulbs flicker
• Turn the light switch off and back
on. Within three minutes, hold
down the Fan Off button while
pressing the Light button twice.
If the problem is not corrected,
repeat the process up to three
times.
before the fan will operate.
Within 3 minutes of restoring power
to the fan, press both the Fan Off
button and the High button for at least
4 seconds. Your fan will turn on low to
indicate successful syncing. If it does
not, turn off power to your fan, wait
1 minute then try again. If using the
transmitter with multiple fans, repeat
this process for each fan.
The Fan Off button only turns the fan
off. To turn the fan on, press one of the
fan speed buttons. They are located
next to the Fan Off button.
Quickly press the Light button to turn
the lights off and on. Hold the Light
button to raise and dim the light level.
High
ooo
Medium
oo
o
Low
HUNTER FAN COMPANY CONTROL LIMITED WARRANTY
The Hunter Fan Company makes the following limited warranty to the original purchaser
of the Control (“Control”):Your Control is warranted to be free from defects in
material and workmanship for a period of one year from the date of sale. If the Control
malfunctions or fails within the warranty period due to a defect in material or workmanship
we will replace it free of charge. IF THE ORIGINAL PURCHASER CEASES TO OWN THE
CONTROL, THIS WARRANTY AND ANY IMPLIED WARRANTY, INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, ARE VOIDED. THIS WARRANTY IS IN LIEU OF ALL OTHER
EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, IN RESPECT TO ANY CONTROL, IS
EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH
ABOVE FOR SUCH CONTROL. This warranty excludes malfunctions or failures which
were caused by repairs by persons not authorized by us, mishandling, improper installation,
modifications, or damage to the Control while in your possession, or unreasonable use.
This warranty does not apply to batteries or to deterioration or damage to the product
caused by the use of faulty batteries. To obtain a replacement, return your Control postage
prepaid along with proof of purchase to Hunter Fan Company Service Department at
7130 Goodlett Farms Pkwy., Memphis, TN 38016. IN NO EVENT SHALL HUNTER
FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
If you have problems installing or operating your fan, do not return this
product to the dealer. Call our Consumer Affairs Hotline.
1-888-830-1326
M0061-01 • 07/26/13 • © Hunter Fan Company
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with RSS-210 of Industry Canada. Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures: Reorient or relocate the receiving antenna, Increase the
separation between the equipment and receiver, Connect the equipment
into an outlet on a circuit different from that to which the receiver is
connected. Consult the dealer or an experienced radio/TV technician for
help. Note: Any changes or modifications to the transmitter or receiver
not expressly approved by Hunter Fan Company may void one’s authority
to operate this remote control.