Sea Gull Lighting 31475-782 Installation Guide

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-1450
112408
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
Read instructions carefully.
Save these instructions.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
BEFORE YOU BEGIN
*OUTLET BOX
MOUNTING
BAR (A)
STEP 2
NUT (B)
GREEN
GROUNDING
SCREW (D)
*OUTLET BOX
SCREWS
NIPPLE (C)
SCREW
COLLAR (E)
STEP 4
CANOPY (H)
CHAIN (K)
SCREW COLLAR
RING (G)
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
INSTALLATION
STEP 3
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
FIXTURE LOOP (J)
STEP 1:
Rotate arms (M).
STEP 2:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Thread screw collar (E) to nipple (C).
ARMS
(M)
STEP 1
STEP 3:
Using 2 pairs of pliers or chain breaks, open one link of chain (S) and
connect it to the fixture loop (J) at the top of the fixture. Do not twist.
STEP 4:
Slide the screw collar ring (G) and canopy (H), in that order, over
chain (K). Open one link on the other end of the chain (K) and attach
it to the screw collar (E) which has been mounted to the nipple (C).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
FIGURE 1
*NOT INCLUDED
INSTALLATION (continued)
HC-1450
STEP 5:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (F) from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or
green insulated wire) around the green grounding screw (D) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire (F) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
*OUTLET BOX
STEP 5
*WIRE
CONNECTORS
GROUND
WIRE (F)
MOUNTING
BAR (A)
NUT (B)
GREEN
GROUNDING
SCREW (D)
STEP 6
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 7:
After wires are connected, tuck them carefully inside outlet box.
Raise canopy (H) against ceiling and thread the screw collar ring (G)
to the screw collar (E).
SCREW
COLLAR (E)
STEP 7
CANOPY (H)
SCREW COLLAR
RING (G)
STEP 8:
Place glass (L) in socket cup (I) and secure by threading retaining
ring (N) onto socket.
CHAIN (K)
STEP 9:
Install lamps (not supplied).
FIXTURE LOOP (J)
STEP 8
SOCKET
CUP (I)
ARMS
(M)
GLASS
(L)
RETAINING
RING (N)
FIGURE 2
*NOT INCLUDED