Sea Gull Lighting 31108-965 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
ASSEMBLY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER SET AT OFF.
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
STEP 1:
GENERAL
You don't need special tools to install this fixture. Be sure to follow
the steps in the order given. Read instructions carefully. If you are
unclear as to how to proceed, consult a qualified electrician.
Spread the fixture arms (R), so that the arms are equally spaced
from each other
STEP 2:
Raise positioning disc (S).
STEP 3:
*WIRE
CONNECTORS
*OUTLET BOX
Secure set screw (Z) with allen wrench provided.
*GROUND WIRE
MOUNTING
BAR (A)
*OUTLET
BOX SCREWS
NUT (B)
NIPPLE (C)
GROUND
WIRE (S)
FIXTURE
ARMS (R)
SCREW COLLAR (D)
CANOPY (E)
CHAIN (G)
SCREW
COLLAR RING (F)
POSITIONING
DISC (S)
FIXTURE
LOOP (I)
SET SCREW
(Z)
FIXTURE
ARMS (R)
BOBECHE
(X)
CANDLE
COVER (Q)
Installation And
Safety Instruction
HC-891 050405
FIGURE 1
*NOT INCLUDED
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
ITEM#_______________
INSTALLATION
HC-891
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are
exposed above nut (B). Thread nipple (C) into mounting bar (A) and
secure with nut (B). Attach screw collar (D) to nipple (C).
STEP 2:
Using 2 pairs of pliers, open one link of chain (G) and connect it to
the fixture loop (I) at the top of the fixture.
STEP 3:
Slide the screw collar ring (F) and canopy (E), in that order, over
chain (G). Open one link on the other end of the chain (G) and
attach it to the screw collar (D) which has been mounted to the
ceiling nipple (C). BE SURE TO CLOSE ALL CHAIN LINKS
COMPLETELY.
STEP 4:
Lace wires up through chain (G) and pass wires through holes in
screw collar (D). We recommend lacing wire up through every other
link of chain (G).
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (R) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (S) from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (R) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire (S) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all
fixtures to have ground wires. These fixtures still meet all UL
specifications. The listing mark of Underwriters on the product
identifies products manufactured under its listing and Follow-Up
Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (E) against ceiling and screw the screw collar
ring (F) to the screw collar (D).
STEP 2:
Install bobeche (X) and candle covers (Q).
STEP 5:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 3:
Install lamps.
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
GROUP B: CONNECT TO WHITE
HOUSE WIRE
GROUNDING AND MOUNTING BAR LOCK UP
WHITE
*OUTLET BOX
*GROUND WIRE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*WIRE
CONNECTORS
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
MOUNTING
BAR (A)
*OUTLET BOX
SCREWS
GREEN
GROUNDING
SCREW (R)
FIGURE 2
NUT (B)
NIPPLE (C)
*NOT INCLUDED