Hunter 59012 Use and Care Manual

www.HunterFan.com
Table of Contents
What to Expect with
Your Installation
Congratulations on purchasing your new
Hunter® ceiling fan! It will provide comfort
and performance in your home or office for
many years. This installation and operation
manual contains complete instructions for
installing and operating your fan.
Tools Needed
Mounting Options
1.888.830.1326
Ceiling Bracket
30 inches
Wiring
11
Troubleshooting
?
?
?
19
PA G E
17
PA G E
1
M3541-01 • 05/14/14 • © Hunter Fan Company
16
10
Operation,
Maintenance & Cleaning
PA G E
13
PA G E
PA G E
12
Remote Control
5
Blades
PA G E
Light Kit
PA G E
Heat Shield
Canopy
9
PA G E
6
Save your receipt for proof of purchase.
4
PA G E
To register your fan, please visit:
www.HunterFan.com/register
3
PA G E
Downrod
Ladder
PA G E
PA G E
We are proud of our work and appreciate
the opportunity to supply you with the best
ceiling fan available anywhere in the world.
2
PA G E
7 feet
www.HunterFan.com
What to Expect with Your Installation
1.888.830.1326
Read and Save These Instructions
This product conforms to UL Standard 507.
If you are unfamiliar
with wiring, use a
qualified electrician.
WARNINGS
w.1 - To reduce the risk of fire, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
30 inches
from blade tip
to nearest wall
or obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
You may need a
friend to help you.
Assess location
1
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Check box to see
fan weight
7 feet
from bottom
edge of blade
to the floor
Assess ceiling angle
2
Standard Downrod
for ceilings 8-10 feet high
Longer Downrod
for ceilings 10 feet or higher
Select a downrod length
2
M3541-01 • 05/14/14 • © Hunter Fan Company
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor damage,
use only Hunter Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualified electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
www.HunterFan.com
Tools Needed
Ladder
Pliers
Wire Strippers
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
M3541-01 • 05/14/14 • © Hunter Fan Company
Screwdrivers
1.888.830.1326
34O
CEILING
www.HunterFan.com
Mounting Options
OPTION 1
If you have a flat ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by a standard downrod (included).
1.888.830.1326
Use Standard Mounting
to hang the fan from a flat ceiling.
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
4
M3541-01 • 05/14/14 • © Hunter Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
Ceiling Bracket
www.HunterFan.com
1.888.830.1326
r
we
o
nP
r
Tu
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
still attached.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Refer to warning w.1 on pg. 2
5
M3541-01 • 05/14/14 • © Hunter Fan Company
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
www.HunterFan.com
1.888.830.1326
skip to next page
Standard
Downrod
for ceilings 8-10’ high
Steps 1-5 to remove standard downrod pipe
1
2
3
4
10
9
8
Steps 6-10 to reassemble with new pipe
6
M3541-01 • 05/14/14 • © Hunter Fan Company
5
Slide
Slide
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Sold Separately
Option 2
If you need a different downrod length follow these steps:
Included
(pre-assembled)
Option 1
Downrod
7
6
www.HunterFan.com
KEEP!
(not to scale)
8”
&
3/8”
1.888.830.1326
STRIP
CUT
Downrod (continued)
!
KEEP
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
3/8”
If the setscrew is not tightened
securely, the fan may fall.
7
M3541-01 • 05/14/14 • © Hunter Fan Company
www.HunterFan.com
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
8
M3541-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Wiring
Note: To connect the
wires, hold the bare
metal leads together and
place a wire connector
over them, then twist
clockwise until tight.
OM CEILING
FR
T
KE
AC
FRO
white
FR
M FA N
OM FAN
FR
OM
white
ING BR
white (grounded)
Using the orange wire
connectors from
the
hardware bag,
connect the black wire
(ungrounded) from
the ceiling to the black
wire from the receiver.
Connect the white
wire (grounded) from
the ceiling to both the
white wire from the
receiver and the white
wire from the fan.
black
CEIL
1.888.830.1326
OM CEILING
FR
black
(ungrounded)
M
blue
green/yellow
stripe
O
FR
Using an orange wire
connector from
the
hardware
bag, connect the
3 grounding wires
(green, green/yellow
stripe, or bare copper)
coming from the
ceiling, downrod, and
hanging bracket.
blue
green/yellow stripe
RECEIV
ER
black
Using the orange
wire connectors
from the remote
control hardware
bag, connect the blue
wire from the receiver
to the blue wire (or
possibly black with
white stripe wire) from
the fan. Connect the
yellow wire from the
receiver to the black
wire from the fan.
OM
FR
yellow
green/yellow
stripe (grounding)
OM FAN
FR
www.HunterFan.com
RECEIV
ER
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
9
M3541-01 • 05/14/14 • © Hunter Fan Company
www.HunterFan.com
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Install the two canopy screws,
found in the
hardware bag.
Note: Fan style may vary.
10
M3541-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Blades
Insert each blade into a slot. Align the holes on
the blade with the holes on the blade ring.
www.HunterFan.com
1.888.830.1326
Attach the blade to the blade ring
using the blade assembly screws,
found in the
hardware bag.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
11
M3541-01 • 05/14/14 • © Hunter Fan Company
Heat Shield
www.HunterFan.com
1.888.830.1326
Machine Screw
Partially install two machine screws, found
in the
hardware bag, halfway into the
motor housing. It does not matter which
two screw holes you choose.
Feed the wires through the center
hole of the heat shield, then wrap the
keyhole slots around the screws and
twist counterclockwise.
Use only the light fixture supplied with this fan model.
12
M3541-01 • 05/14/14 • © Hunter Fan Company
Insert the third screw, found in
the
hardware bag, into place and
then tighten all three screws.
Make sure the heat shield assembly is securely attached to
the housing mounting plate. Failure to properly attach and
tighten all three assembly screws could result in the heat
shield assembly and light fixture falling.
www.HunterFan.com
Light Kit
1.888.830.1326
Machine Screw
Partially install two machine screws, found
in the
hardware bag, into the screw
holes in the heat shield.
Connect the plug connectors between
the black wire coming from the light kit
and the blue wire coming from the motor
housing. Connect the plug connectors
between the white wire coming from the
light kit and the white wire coming from
the motor housing.
13
M3541-01 • 05/14/14 • © Hunter Fan Company
Align the keyholes in the light kit assembly
with the two machine screws. Lift the light
kit assembly and turn it counter clockwise
until the screws are resting in the narrow
end of the keyhole slots.
www.HunterFan.com
Light Kit (continued)
Install the third machine screw, found in
the
hardware bag, into the light kit.
Make sure the light kit is securely attached to the heat shield.
Failure to properly secure all three assembly screws could
result in the light fixture falling.
Tighten all three screws securely.
1.888.830.1326
Install a light bulb in each socket.
Note: Do not use CFL bulbs to replace
your light bulbs. Your lights may flicker
or fail to work.
14
M3541-01 • 05/14/14 • © Hunter Fan Company
Note: In compliance with US federal energy regulations, this ceiling fan
contains a device that restricts its light output. Exceeding the wattage
limit marked on the MAX wattage sticker affixed to the light socket(s)
may result in fire hazard or improper operation.
www.HunterFan.com
Light Kit (continued)
1.888.830.1326
Screw
Holes
Decorative
Screw
CONGRA
YOU’RETULATIONS!
DONE!
Glass Bowl
Lift the glass bowl and align the screw
holes in the glass bowl with the screw
holes in the metal rods coming from
the heat shield.
Install the decorative screws into the metal
rods to secure the glass bowl in place.
15
M3541-01 • 05/14/14 • © Hunter Fan Company
See next page for remote
operation instructions.
www.HunterFan.com
Remote Control
1.888.830.1326
If you are installing multiple remote-controlled fans on
the same circuit breaker, you may need to perform a few
extra steps to prevent interference or faulty operation of
your remote controls.
Go to www.HunterFan.com/FAQs and click
“How do I properly install multiple remote-controlled fans?”
for more information.
Battery
Door
Fan Off
High
Phillips
Head
Screw
To access the battery compartment, remove
the small Phillips head screw that secures the
battery door to the transmitter assembly. The
battery should be installed with the positive
(+) side up. Replace with a CR2032 battery
when necessary.
r
we
o
nP
r
Tu
ON
16
M3541-01 • 05/14/14 • © Hunter Fan Company
Note: The remote must be paired before
the fan will operate.
Within 3 minutes of restoring power to
the fan, press both the Fan Off button and
the High button for at least 4 seconds. Your
fan will turn on low to indicate successful
syncing. If it does not, turn off power to your
fan, wait 1 minute then try again. If using the
transmitter with multiple fans, repeat this
process for each fan.
Operation, Maintenance, & Cleaning
www.HunterFan.com
1.888.830.1326
Medium
Speed
Fan
Off
High
Speed
Reverse
Switch
Switch Cover Plate
Low
Speed
Light
Removed
Tabs
To turn on fan, press a fan speed button.
Speeds range from off (0) to high (3). Quickly
press the Light button to turn the lights off
and on. Hold the Light button to raise and
dim the light level.
Rocker- Style
Plate
To install the transmitter cradle, remove the
two screws holding the switch cover plate. Do
not remove the cover plate. Orient the cradle
by lining up the two mounting holes with
those on the cover plate. Insert and tighten
the screws. Do not over tighten.
Note: For rocker-style cover plates, break off
the tabs by pushing outward.
17
M3541-01 • 05/14/14 • © Hunter Fan Company
To switch the direction of air flow, move the
reverse switch to the opposite position.
Operation, Maintenance, & Cleaning (continued)
www.HunterFan.com
1.888.830.1326
Safe-Exit
The Safe-Exit Program gives you about thirty
seconds of light when you turn the lights off
to exit the room before the lights go out. To
use Safe-Exit:
• Press the Fan Off button for at least three
seconds to initiate the Safe-Exit Mode.
• The lights will flash for visual
confirmation.
• The lights will stay on 50% brightness for
15 seconds and then begin to dim. After
a total of 30 seconds, the lights will be
completely off.
To replace the bulbs, remove the
decorative screws while supporting the
glass bowl with one hand. Carefully
remove the glass bowl. Unscrew the
bulbs and replace them with bulbs of
the same type and wattage. Reinstall the
glass bowl assembly.
When cleaning the fan, use soft brushes
or cloths to prevent scratching. Cleaning
products may damage the finishes.
18
M3541-01 • 05/14/14 • © Hunter Fan Company
www.HunterFan.com
Troubleshooting
Fan doesn’t work
Excessive wobbling
Noisy operation
• Make sure power switch is on.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Tighten the blade and blade
iron screws until they are snug.
• Pull the pull chain to make sure
it is on.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Use the provided balancing
kit and instructions to balance
the fan.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 9.
Remote control of fan is erratic
• Check the plug connection in
the switch housing.
• Install a fresh battery.
If you have multiple remotes or
multiple remote-controlled fans
installed on the same circuit
breaker and you are experiencing
interference or faulty operation of
your remote controls, please go to
www.HunterFan.com/FAQs
and click “How do I properly install
multiple remote-controlled fans?”
for information on how to correct
this issue.
• Make sure the battery is
installed correctly.
Transmitter only works when
held at close range
• Change battery.
19
M3541-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Lights dim when turned on or do not turn on at all.
• Make sure the wattage of the
light bulbs installed matches
the specifications on the light
sockets.
Download PDF
Similar pages
Hunter 99121 fan
Hunter 52" Sonic
Hunter 52" Bridgeport
Hunter Kensington New
Hunter 99120 Instructions / Assembly
Hunter 53082 fan
Hunter 59033 fan
Hunter 53116 Use and Care Manual