Hunter 59013 Use and Care Manual

www.HunterFan.com
Table of Contents
What to Expect with
Your Installation
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
Tools Needed
Mounting Options
1.888.830.1326
Ceiling Bracket
30 inches
Downrod
Troubleshooting
?
?
?
18
PA G E
1
M3522-01 • 05/14/14 • © Hunter Fan Company
16
PA G E
14
PA G E
13
PA G E
PA G E
12
10
Operation, Maintenance
& Cleaning
Light Kit
11
Canopy
PA G E
Switch Housing
PA G E
Blades
7
PA G E
6
Save your receipt for proof of purchase.
Wiring
5
PA G E
To register your fan, please visit:
www.HunterFan.com/register
4
PA G E
Preparation
3
PA G E
Ladder
PA G E
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
2
PA G E
7 feet
www.HunterFan.com
What to Expect with Your Installation
1.888.830.1326
Read and Save These Instructions
This product conforms to UL Standard 507.
If you are unfamiliar
with wiring, use a
qualified electrician.
WARNINGS
w.1 - To reduce the risk of fire, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
30 inches
from blade tip
to nearest wall
or obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
You may need a
friend to help you.
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Check box to see
fan weight
7 feet
from bottom
edge of blade
to the floor
Assess ceiling angle
Assess location
1
Standard Downrod
2
Shorter Downrod
for ceilings 8-10 feet high
for fans installed close to ceiling
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor damage,
use only Hunter Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualified electrician.
c.2 - Use only Hunter replacement parts.
3
Longer Downrod
for ceilings 10 feet or higher
Select a downrod length
2
M3522-01 • 05/14/14 • © Hunter Fan Company
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
www.HunterFan.com
Tools Needed
Ladder
Pliers
Wire Strippers
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
M3522-01 • 05/14/14 • © Hunter Fan Company
Screwdrivers
1.888.830.1326
34O
CEILING
www.HunterFan.com
Mounting Options
OPTION 1
If you have a flat ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by a standard downrod (included).
1.888.830.1326
1.866.268.1936
Use Standard Mounting
or Low-Profile Mounting
to hang the fan from a flat ceiling.
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
4
M3522-01 • 05/14/14 • © Hunter Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
Ceiling Bracket
www.HunterFan.com
1.888.830.1326
For angled ceilings, point
opening toward peak.
er
w
o
nP
r
Tu
OFF
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four (4) bumpers
are still attached.
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Refer to warning w.1 on pg. 2
5
M3522-01 • 05/14/14 • © Hunter Fan Company
Preparation
www.HunterFan.com
1.888.830.1326
A
ISC R
D
D
Ceiling Bracket (continued)
DISC
D
AR
If you are installing multiple remote-controlled
fans on the same circuit breaker,
you may need to perform a few extra steps to
prevent interference or faulty operation of your
remote controls.
Go to www.HunterFan.com/FAQs and click
“How do I properly install multiple remotecontrolled fans?” for more information.
Remove the shipping blocks from the
motor. Discard the screws.
Note: Some fans will have a shipping
ring instead of shipping blocks. Please
remove the ring and discard the screws.
6
M3522-01 • 05/14/14 • © Hunter Fan Company
www.HunterFan.com
Option 1
Downrod
1.888.830.1326
skip to next page
Standard
Downrod
for ceilings 8-10’ high
Steps 1-5 to remove standard downrod pipe
1
2
4
Sold Separately
Slide
3
10
9
8
Steps 6-10 to reassemble with new pipe
7
M3522-01 • 05/14/14 • © Hunter Fan Company
5
Slide
Option 3
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Shorter
Downrod
for fans installed
close to ceiling
Included
Option 2
Included
(pre-assembled)
If you need a different downrod length follow these steps:
7
6
www.HunterFan.com
KEEP!
(not to scale)
8”
&
3/8”
1.888.830.1326
STRIP
CUT
Downrod (continued)
!
KEEP
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
3/8”
If the setscrew is not tightened
securely, the fan may fall.
8
M3522-01 • 05/14/14 • © Hunter Fan Company
www.HunterFan.com
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
Note: Fan style may vary.
9
M3522-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Wiring
Note: To connect the
wires, hold the bare
metal leads together and
place a wire connector
over them, then twist
clockwise until tight.
OM CEILING
FR
T
KE
AC
FRO
white
FR
M FA N
OM FAN
FR
OM
white
ING BR
white (grounded)
Using the orange wire
connectors from
the
hardware bag,
connect the black wire
(ungrounded) from
the ceiling to the black
wire from the receiver.
Connect the white
wire (grounded) from
the ceiling to both the
white wire from the
receiver and the white
wire from the fan.
black
CEIL
1.888.830.1326
OM CEILING
FR
black
(ungrounded)
M
blue
green/yellow
stripe
O
FR
Using an orange wire
connector from
the
hardware
bag, connect the
3 grounding wires
(green, green/yellow
stripe, or bare copper)
coming from the
ceiling, downrod, and
hanging bracket.
blue
green/yellow stripe
black
Using the orange
wire connectors
from the remote
control hardware
bag, connect the blue
wire from the receiver
to the blue wire (or
possibly black with
white stripe wire) from
the fan. Connect the
yellow wire from the
receiver to the black
wire from the fan.
RECEIV
ER
OM
FR
yellow
green/yellow
stripe (grounding)
OM FAN
FR
www.HunterFan.com
RECEIV
ER
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
10
M3522-01 • 05/14/14 • © Hunter Fan Company
www.HunterFan.com
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the
hardware bag.
Note: Fan style may vary.
11
M3522-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Blades
Install the grommets, found in the
hardware
bag, in the blades by hand. Place each blade
between a blade iron and medallion. Install three
blade screws, found in the hardware bag, to
attach the medallion to the blade iron. Repeat
for all blades.
www.HunterFan.com
1.888.830.1326
Lightly attach the blade irons to the
motor with screws found in
the
hardware bag, then securely
tighten after both screws are attached.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
12
M3522-01 • 05/14/14 • © Hunter Fan Company
Switch Housing
Screw two housing assembly screws
from the
hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing fixture falling.
www.HunterFan.com
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
13
M3522-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Insert the third screw, found in
the
hardware bag, into place and
then tighten all three screws.
www.HunterFan.com
Light Kit
1.888.830.1326
Screw
Holes
Connect the plugs from the upper and
lower switch housings. Make sure to line up
the colored markings on the connectors.
Place the light kit over the upper switch
housing and align the screw holes.
14
M3522-01 • 05/14/14 • © Hunter Fan Company
Install three housing screws, found
in the
hardware bag. Tighten all
three screws securely.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light fixture falling.
www.HunterFan.com
Light Kit (continued)
1.888.830.1326
Tab
Bulb
Notch
CONGRA
YOU’RETULATIONS!
DONE!
Install the included CFL bulbs into
the sockets. When necessary, replace
with bulbs of same wattage.
Lift the globe and align the notches in the
globe with the tabs in the light kit. Attach
the glass bowl to the light kit by twisting it
clockwise until it snaps into place.
Note: Globe style and number of
lights may vary.
15
M3522-01 • 05/14/14 • © Hunter Fan Company
See next page for fan
operation instructions.
Operation, Maintenance, & Cleaning
www.HunterFan.com
1.888.830.1326
High
Medium
Low
Fan Off
Battery
Door
Light
High
Fan Off
Phillips
Head
Screw
To access the battery compartment,
remove the small Phillips head screw
that secures the battery door to the
transmitter assembly. The battery
should be installed with the positive
(+) side up. Replace with a CR2032
battery when necessary.
Turn Power
ON
Note: The remote must be paired
before the fan will operate.
Within 3 minutes of restoring power
to the fan, press both the Fan Off
button and the High button for at
least 4 seconds. Your fan will turn on
low to indicate successful syncing.
If it does not, turn off power to your
fan, wait 1 minute then try again. If
using the transmitter with multiple
fans, repeat this process for each fan.
The Fan Off button only turns the
fan off. To turn the fan on, press one
of the fan speed buttons.
ooo
High
oo
Medium
o
Low
Quickly press the Light button to
turn the lights off and on.
16
M3522-01 • 05/14/14 • © Hunter Fan Company
To install the transmitter cradle,
remove the two screws holding
your switch cover plate. Do not
remove the cover plate. Orient
the cradle by lining up the two
mounting holes with those on the
cover plate. Insert and tighten the
screws. Do not over tighten.
Operation, Maintenance, & Cleaning (continued)
www.HunterFan.com
1.888.830.1326
Safe-Exit
The Safe-Exit Program gives
you about thirty seconds of light
when you turn the lights off to
exit the room before the lights go
out. To use Safe-Exit:
• Press the Fan Off button for at
least three seconds to initiate the
Safe-Exit Mode.
• The lights will flash for visual
confirmation.
Reverse
Switch
• The lights will stay on 50%
brightness for 15 seconds and
then begin to dim. After a total
of 30 seconds, the lights will be
completely off.
Note: For CFL lighting, the lights
will stay on 100% brightness for 30
seconds. After a total of 30 seconds,
the lights will be completely off.
To switch the direction of air flow, move
the reverse switch to the opposite
position. You will need to remove the
light kit glass to do so.
17
M3522-01 • 05/14/14 • © Hunter Fan Company
For cleaning the fan, use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the finishes.
www.HunterFan.com
Troubleshooting
Fan doesn’t work
Excessive wobbling
Noisy Operation
• Make sure power switch is on.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Tighten the blade and blade
iron screws until they are snug.
• Pull the pull chain to make sure
it is on.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Use the provided balancing
kit and instructions to balance
the fan.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 10.
Remote control of fan is erratic
• Check the plug connection in
the switch housing.
• Install a fresh battery.
• Make sure the battery is
installed correctly.
Transmitter only works when
held at close range
• Install a fresh battery.
18
M3522-01 • 05/14/14 • © Hunter Fan Company
If you have multiple remotes or
multiple remote-controlled fans
installed on the same circuit
breaker and you are experiencing
interference or faulty operation of
your remote controls, please go to
www.HunterFan.com/FAQs
and click “How do I properly install
multiple remote-controlled fans?”
for information on how to correct
this issue.
1.888.830.1326
Download PDF
Similar pages
Hunter 59072 Use and Care Manual
Hunter 52" Sonic
Hunter 99121 fan
Hunter 53102 fan
Hunter 59054 Installation Guide
Hunter Kensington New
Hunter 52001 Installation Guide
Hunter 54" Bayview