Hunter 59072 Use and Care Manual

www.HunterFan.com
Table of Contents
Tools Needed
Mounting Options
Ceiling Bracket
30 inches
To register your fan, please visit:
www.HunterFan.com/register
4
Wiring
Canopy
Operation,
Maintenance & Cleaning
Light Kit
Troubleshooting
?
?
14
PA G E
1
M3551-01 • 05/14/14 • © Hunter Fan Company
12
PA G E
PA G E
10
8
?
5
9
Blades
PA G E
7
PA G E
PA G E
6
Save your receipt for proof of purchase.
3
PA G E
Downrod
Ladder
PA G E
2
PA G E
7 feet
PA G E
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
What to Expect with
Your Installation
PA G E
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
1.888.830.1326
www.HunterFan.com
What to Expect with Your Installation
1.888.830.1326
Read and Save These Instructions
This product conforms to UL Standard 507.
If you are unfamiliar
with wiring, use a
qualified electrician.
WARNINGS
w.1 - To reduce the risk of fire, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
30 inches
from blade tip
to nearest wall
or obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
You may need a
friend to help you.
Assess location
1
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Check box to see
fan weight
7 feet
from bottom
edge of blade
to the floor
Assess ceiling angle
2
Standard Downrod
for ceilings 8-10 feet high
Longer Downrod
for ceilings 10 feet or higher
Select a downrod length
2
M3551-01 • 05/14/14 • © Hunter Fan Company
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor damage,
use only Hunter Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualified electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
www.HunterFan.com
Tools Needed
Ladder
Pliers
Wire Strippers
Screwdrivers
If you are installing multiple remote-controlled
fans on the same circuit breaker,
you may need to perform a few extra steps to
prevent interference or faulty operation of your
remote controls.
Power Drill
(optional)
Go to www.HunterFan.com/FAQs and click
“How do I properly install multiple remotecontrolled fans?” for more information.
9/64” Drill Bit
(optional)
If mounting to a support structure, you will also need these tools.
3
M3551-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
34O
CEILING
www.HunterFan.com
Mounting Options
OPTION 1
If you have a flat ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by a standard downrod (included).
1.888.830.1326
1.866.268.1936
Use Standard Mounting
to hang the fan from a flat ceiling.
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
4
M3551-01 • 05/14/14 • © Hunter Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
www.HunterFan.com
Ceiling Bracket
1.888.830.1326
r
we
o
nP
r
Tu
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
still attached.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Refer to warning w.1 on pg. 2
5
M3551-01 • 05/14/14 • © Hunter Fan Company
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
www.HunterFan.com
(not to scale)
8”
&
3/8”
STRIP
CUT
Downrod
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Put the wires and downrod through
the canopy. Let the canopy sit
loosely on top of the fan.
DO NOT PICK THE FAN UP BY
THE CANOPY OR WIRES. Place the
downrod ball into the slot in the
ceiling bracket.
8”
3/8”
6
M3551-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Wiring
Note: To connect the
wires, hold the bare
metal leads together and
place a wire connector
over them, then twist
clockwise until tight.
OM CEILING
FR
T
KE
AC
FRO
white
FR
M FA N
OM FAN
FR
OM
white
ING BR
white (grounded)
Using the orange wire
connectors from
the
hardware bag,
connect the black wire
(ungrounded) from
the ceiling to the black
wire from the receiver.
Connect the white
wire (grounded) from
the ceiling to both the
white wire from the
receiver and the white
wire from the fan.
black
CEIL
1.888.830.1326
OM CEILING
FR
black
(ungrounded)
M
blue
green/yellow
stripe
O
FR
Using an orange wire
connector from
the
hardware
bag, connect the
3 grounding wires
(green, green/yellow
stripe, or bare copper)
coming from the
ceiling, downrod, and
hanging bracket.
blue
green/yellow stripe
RECEIV
ER
black
Using the orange
wire connectors
from the remote
control hardware
bag, connect the blue
wire from the receiver
to the blue wire (or
possibly black with
white stripe wire) from
the fan. Connect the
yellow wire from the
receiver to the black
wire from the fan.
OM
FR
yellow
green/yellow
stripe (grounding)
OM FAN
FR
www.HunterFan.com
RECEIV
ER
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
7
M3551-01 • 05/14/14 • © Hunter Fan Company
www.HunterFan.com
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the
hardware bag.
Note: Fan style may vary.
8
M3551-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Blades
www.HunterFan.com
Insert a blade into the motor housing.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
Attach each blade to the fan using two
blade grommets, found in the
hardware
bag, and two blade assembly screws, found
in the
hardware bag.
9
M3551-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
www.HunterFan.com
Light Kit
1.888.830.1326
Light Kit
Assembly
Screw
Partially install two of the light kit assembly
screws, found in the
hardware bag.
Align the keyholes in the light kit ring with the
partially installed screws. Lift the light kit ring
in place and rotate counterclockwise to situate
the screws in the narrow ends of the keyholes.
10
M3551-01 • 05/14/14 • © Hunter Fan Company
Insert the third screw, found in
the
hardware bag, into place and
then tighten all three screws.
Make sure the light kit ring is securely attached.
Failure to properly secure all three assembly screws
could result in the light fixture falling.
www.HunterFan.com
Light Kit (continued)
1.888.830.1326
Tab
CONGRA
Notch
YOU’RETULATIONS!
DONE!
Bulb
Install the included 18W CFL
bulb. When necessary, replace
with bulbs of same wattage.
Position the notches in the outer
rim of the globe so they line up
with the tabs on the light kit ring.
Carefully lift the globe up inside
the light fixture as far as it will go.
Rotate the globe in a clockwise
direction until it is held tightly in
place by the three tabs.
11
M3551-01 • 05/14/14 • © Hunter Fan Company
See next page for fan
operation instructions.
Operation, Maintenance, & Cleaning
www.HunterFan.com
Fan
Off
1.888.830.1326
Medium
Speed
High
Speed
Switch
Cover Plate
Battery
Door
Low
Speed
Light
Fan Off
High
Phillips
Head
Screw
Removed
Tabs
To access the battery compartment,
remove the small Phillips head screw
that secures the battery door to the
transmitter assembly. The battery
should be installed with the positive
(+) side up. Replace with a CR2032
battery when necessary.
Turn Power
ON
Note: The remote must be paired
before the fan will operate.
Within 3 minutes of restoring power
to the fan, press both the Fan Off
button and the High button for at
least 4 seconds. Your fan will turn on
low to indicate successful syncing.
If it does not, turn off power to your
fan, wait 1 minute then try again. If
using the transmitter with multiple
fans, repeat this process for each fan.
To turn on fan, press a fan speed
button. Speeds range from off (0)
to high (3). Quickly press the Light
button to turn the lights off and on.
12
M3551-01 • 05/14/14 • © Hunter Fan Company
RockerStyle Plate
To install the transmitter cradle, remove
the two screws holding the switch
cover plate. Do not remove the cover
plate. Orient the cradle by lining up
the two mounting holes with those on
the cover plate. Insert and tighten the
screws. Do not over tighten.
Note: For rocker-style cover plates,
break off the tabs by pushing outward.
Operation, Maintenance, & Cleaning (continued)
www.HunterFan.com
1.888.830.1326
Safe-Exit
The Safe-Exit Program gives
you about thirty seconds of light
when you turn the lights off to
exit the room before the lights go
out. To use Safe-Exit:
Reverse
Switch
• Press the Fan Off button for at
least three seconds to initiate the
Safe-Exit Mode.
• The lights will flash for visual
confirmation.
• The lights will stay on 50%
brightness for 15 seconds and
then begin to dim. After a total
of 30 seconds, the lights will be
completely off.
Note: For CFL lighting, the lights
will stay on 100% brightness for 30
seconds. After a total of 30 seconds,
the lights will be completely off.
To switch the direction of air flow, move
the reverse switch to the opposite
position. You will need to remove the
light kit glass to do so.
13
M3551-01 • 05/14/14 • © Hunter Fan Company
For cleaning the fan, use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the finishes.
www.HunterFan.com
Troubleshooting
Fan doesn’t work
Excessive wobbling
• Make sure power switch is on.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Use the provided balancing
kit and instructions to balance
the fan.
• Make sure the blades spin freely.
Noisy Operation
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 7.
• Tighten the blade and blade
iron screws until they are snug.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Check the plug connection in
the switch housing.
Remote control of fan is erratic
• Make sure the battery is
installed correctly.
• Install a fresh battery.
Transmitter only works when
held at close range
• Install a fresh battery.
If you have multiple remotes or
multiple remote-controlled fans
installed on the same circuit
breaker and you are experiencing
interference or faulty operation of
your remote controls, please go to
www.HunterFan.com/FAQs
and click “How do I properly install
multiple remote-controlled fans?”
for information on how to correct
this issue.
14
M3551-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Hunter fans have the power to cut your cooling costs up
to 40%.
Beat the High Cost of Cooling
The air movement created by a Hunter ceiling fan
lets you set your thermostat higher and still stay
comfortable. Every degree you raise the thermostat
saves up to 7% on energy costs. So, you can cut back on
expensive air conditioning ... and save up to 40%* on
cooling. In winter, your Hunter fan recirculates warm air
and saves up to 10%* on heating bills.
* On average at low speed settings. Your savings may
vary based on climate, building type and thermostat
setting.
Save Energy and Money While Protecting
the Environment
Congratulations! You’re saving energy and money while
protecting the environment by purchasing this ENERGY
STAR qualified Hunter ceiling fan! With this purchase, you
are doing your part to protect the environment.
Your new ceiling fan has earned the ENERGY STAR label
because it meets high energy efficiency specifications
set by the Environmental Protection Agency (EPA).
ENERGY STAR labeled ceiling fans save energy because
they have more efficient fan motors and air delivery due
to more aerodynamic blade configurations. Ceiling fan
models bearing the ENERGY STAR label move air 14 20% more efficiently than typical ceiling fan models.
For more information on ENERGY STAR visit
www.energystar.gov.