Hunter 52017 Instructions / Assembly

www.HunterFan.com
Table of Contents
What to Expect with
Your Installation
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
Tools Needed
1.866.268.1936
Preparation
Ceiling Bracket
30 inches
PA G E
?
?
?
15
PA G E
1
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
14
Troubleshooting
PA G E
12
9
PA G E
PA G E
8
PA G E
11
5
Motor Housing
Maintenance,
Operation & Cleaning
Light Kit
PA G E
PA G E
10
Wiring
PA G E
Switch Housing
Blades
4
PA G E
7
PA G E
6
Save your receipt for proof of purchase.
3
Secondary Hanging
System
Hanging the Fan
To register your fan, please visit:
www.HunterFan.com/register
Ladder
PA G E
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
2
PA G E
7 feet
www.HunterFan.com
What to Expect with Your Installation
Read and Save These Instructions
If you are unfamiliar
with wiring, use a
qualified electrician.
This product conforms to UL Standard 507.
WARNINGS
30 inches
from blade tip
to nearest wall
or obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
7 feet
from bottom
edge of blade
to the floor
Know your wiring
1.866.268.1936
Assess location
w.1 - To reduce the risk of fire, electrical shock, or
personal injury, mount fan directly from building
structure and/or an outlet box marked acceptable for
fan support of 70 lbs (31.8 kg) and use the mounting
screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing
or servicing your fan, disconnect the power by turning
off the circuit breakers to the outlet box and associated
wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent
warning device, such as a tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor
damage, use only Hunter Solid State Speed Controls.
You may need a
friend to help you.
w.4 - To reduce the risk of personal injury, do not bend the
blade brackets when installing the blade brackets, balancing
the blades, or cleaning the fan. Do not insert foreign objects
in between rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and
local electrical codes ANSI/NFPA 70. If you are unfamiliar
with wiring, use a qualified electrician.
c.2 - Use only Hunter replacement parts.
Check box to see
fan weight
2
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
www.HunterFan.com
Tools Needed
Ladder
Power Drill
(optional)
Screwdrivers
9/64” Drill Bit
(optional)
If mounting to a support structure, you will also need these tools.
3
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.866.268.1936
www.HunterFan.com
Ceiling Bracket
1.866.268.1936
Bumper
er
w
o
nP
r
Tu
OFF
Make sure all four bumpers are still attached.
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the
outlet box associated with the wall switch location.
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Refer to warning w.1 on pg. 2
4
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Ceiling Bracket (continued)
Preparation
www.HunterFan.com
Time Saver Tip: Get a helper
to insert grommets, found in
the
hardware bag, into the
blades while you’re doing the
next couple of steps.
5
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.866.268.1936
www.HunterFan.com
Hanging the Fan
Ground
Wire
Screw
Hole
While holding the wires out of the way, lift
the motor assembly and place the square
hanger into the opening in the ceiling
bracket. Be sure the ground wire attached
to the hanger faces out of the large
opening in the ceiling bracket.
Locking
Screw
Once the motor is in the ceiling
bracket, use the two locking screws
found in the
hardware bag to secure
the motor to the ceiling bracket.
Note: Fan style may vary.
6
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.866.268.1936
www.HunterFan.com
Secondary Hanging System
3mm (1/8")
1.866.268.1936
Braided
Cable
Support
Brace
Outlet Box
Insert the looped end of the
braided cable through the ceiling
bracket and one of the holes in the
outlet box into the ceiling. Access
the support brace in the ceiling.
You may not be able to do this from
below the ceiling depending on
your installation site.
Ceiling
Drive the wood screw and
washer found in the
bag
into the side of the support
brace that holds the outlet box.
Leave 3 mm (1/8”) of space
between the support brace
and the washer.
Wrap the braided cable around
the support brace once creating
a complete circle. Hook the
looped end of the cable over the
wood screw so that the cable
lies between the washer and the
support brace.
7
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Tighten the loop and secure the
screw and washer all the way
down to the support brace. Coil
up the excess cable.
Wiring
OM
FR
CEILIN
www.HunterFan.com
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
G
OM
FR
T
KE
Black
FR
(Ungrounded)
M FA N
Blue
FRO
(Ungrounded)
AC
Blue
ING BR
Black
CEIL
White
M
Using the orange wire
connectors from
the
hardware bag, connect
the black wire (ungrounded)
from the ceiling to the black
and the blue wires from the
fan. Connect the white wire
(grounded) from the ceiling to
the white wire from the fan.
Using the orange wire
connectors from
the
hardware bag,
connect the white wire
(grounded) from the
ceiling to the white wire
from the fan.
Connect the black wire
(ungrounded) from the
ceiling to the black wire
from the fan. Connect the
second (ungrounded) wire
from the ceiling to the blue
wire from the fan.
White
Green/Yellow
Stripe
FR
O
For a Single Switch
For Dual Switches
(Grounded)
Green/Yellow
Stripe
Using an orange wire
connector from
the
hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, fan, and hanging
bracket.
CEILIN
OM
G
FR
G
(Ungrounded)
(Grounded)
(Grounding)
OM FAN
FR
CEILIN
1.866.268.1936
O M FA N
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
8
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
www.HunterFan.com
Motor Housing
Notch
Motor
Housing
Screw
Indentation
Screw
Holes
Raise the motor housing up over the motor
and ceiling bracket. Turn the motor housing
so the screw holes align and the indentation
in the housing locks into place with the notch
in the ceiling bracket. The motor housing is
not secured until the next step is complete.
Do not leave unattended.
With a Phillips head screwdriver, install
the four motor housing screws found
in the
hardware bag. Tighten all four
screws securely.
9
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.866.268.1936
Blades
www.HunterFan.com
Insert grommets found in the
hardware
bag into the holes in the blades, then
secure each blade to a blade iron with
screws found in the
hardware bag.
Lightly attach the blade irons to the
motor with screws found in
the
hardware bag, then securely
tighten after both screws are attached.
10
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.866.268.1936
www.HunterFan.com
Switch Housing
Screw two housing assembly screws
from the
hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
1.866.268.1936
Insert the third screw, found in
the
hardware bag, into place and
then tighten all three screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all three assembly screws could result in the
switch housing fixture falling.
11
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
www.HunterFan.com
Light Kit
1.866.268.1936
Notch
Switch
Housing
Screw
Partially install two of the switch housing
screws found in the
bag. Connect
the plugs from the upper and lower
switch housings. Make sure to line up the
colored markings on the connectors.
Want to install your fan without a light kit?
Go to www.HunterFan.com/FAQs and click
“How do I install my fan without the light kit?”
Switch
Housing
Screw
Align the notches in the sides of the lower
switch housing with the upper switch
housing screws. Lift the lower switch housing.
Twist the lower switch housing clockwise
to lock into place. Then thread the fan
pull chain through the hole in the light kit.
12
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Install the third switch housing screw.
Tighten all three screws securely.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light fixture falling.
www.HunterFan.com
Light Kit (continued)
Metal
Plate
Light
Pull
Chain
1.866.268.1936
Fan
Pull
Chain
Globe
Globe
Keeper
Finial
Cap
CONGRA
YOU’RETULATIONS!
DONE!
Finial
Install a bulb into each of
the sockets. When necessary,
replace with bulbs of the same
type and wattage.
Note: Glass shade style and
number of lights may vary.
Press the globe and globe keeper
flush against the metal plate. Thread
the light pull chain through the hole
in the center of the finial cap and
thread the fan pull chain through the
hole in the side of the cap. Finally,
thread only the light pull chain
through the hole in the finial and
screw the finial onto the threaded rod.
Connect the appropriate pull
chain pendant to each of the short
chains coming from the finial
and finial cap. The fan pull chain
controls the speed: from high to
off. The light pull chain controls
the light fixture: on and off.
13
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
See next page for fan
operation instructions.
Note: In compliance with Canadian federal energy regulations, this
ceiling fan contains a device that restricts its light output. Exceeding
the wattage limit marked on the MAX wattage sticker affixed to the
light socket(s) may result in fire hazard or improper operation.
Maintenance, Operation & Cleaning
r
we
o
nP
www.HunterFan.com
1.866.268.1936
Metal
Plate
r
Tu
ON
Globe
Globe
Keeper
Finial
Cap
Reverse
Switch
Finial
Changing the bulbs - unscrew
the finial and remove it from the
threaded rod. Remove the finial cap
and unscrew the globe keeper while
supporting the globe with your other
hand. Carefully remove the globe.
Unscrew bulbs and replace with
bulbs of same type and wattage.
Reinstall the globe assembly.
Changing the direction of air
flow - move the reverse switch
to the opposite position.
14
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Cleaning the fan - use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the finishes.
For questions regarding removing a light kit, call
customer service 1-866-268-1936.
www.HunterFan.com
Troubleshooting
Fan doesn’t work
Excessive wobbling
Noisy Operation
• Make sure power switch is on.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Tighten the blade and blade
iron screws until they are snug.
• Pull the pull chain to make sure
it is on.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Use the provided balancing
kit and instructions to balance
the fan.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 8.
• Check the plug connection in
the switch housing.
15
M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
1.866.268.1936
Lights dim when turned on or do not turn on at all.
• Make sure the wattage of the
light bulbs installed matches
the specifications on the light
sockets.