Hunter 59054 Installation Guide

Table of Contents
1.888.830.1326
Ceiling Bracket
30 inches
Ladder
Downrod
3
Wiring
10
Operation, Maintenance
& Cleaning
Light Kit
11
Troubleshooting
?
?
?
17
PA G E
15
PA G E
1
M3519-01 • 05/14/14 • © Hunter Fan Company
PA G E
PA G E
13
5
Blades
PA G E
9
Switch Housing
12
Canopy
PA G E
6
4
PA G E
2
PA G E
7 feet
PA G E
Save your receipt for proof of purchase.
Mounting Options
PA G E
To register your fan, please visit:
www.HunterFan.com/register
Tools Needed
PA G E
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
What to Expect with
Your Installation
PA G E
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
www.HunterFan.com
What to Expect with Your Installation
www.HunterFan.com
1.888.830.1326
Read and Save These Instructions
This product conforms to UL Standard 507.
If you are unfamiliar
with wiring, use a
qualified electrician.
WARNINGS
w.1 - To reduce the risk of fire, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
30 inches
from blade tip
to nearest wall
or obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
You may need a
friend to help you.
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Check box to see
fan weight
7 feet
from bottom
edge of blade
to the floor
Assess ceiling angle
Assess location
1
Standard Downrod
2
Shorter Downrod
for ceilings 8-10 feet high
for fans installed close to ceiling
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor damage,
use only Hunter Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualified electrician.
c.2 - Use only Hunter replacement parts.
3
Longer Downrod
for ceilings 10 feet or higher
Select a downrod length
2
M3519-01 • 05/14/14 • © Hunter Fan Company
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
Tools Needed
Ladder
www.HunterFan.com
Pliers
Wire Strippers
1.888.830.1326
Screwdrivers
If you are installing multiple remote-controlled
fans on the same circuit breaker,
you may need to perform a few extra steps to
prevent interference or faulty operation of your
remote controls.
Allen Wrench
(included)
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
M3519-01 • 05/14/14 • © Hunter Fan Company
Go to www.HunterFan.com/FAQs and click
“How do I properly install multiple remotecontrolled fans?” for more information.
34O CEILING
Mounting Options (continued)
Mounting Options
OPTION 1
If you have a flat ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
1.888.830.1326
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by a standard downrod (included).
www.HunterFan.com
Use Standard Mounting
or Low-Profile Mounting
to hang the fan from a flat ceiling.
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
4
M3519-01 • 05/14/14 • © Hunter Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
Ceiling Bracket
www.HunterFan.com
1.888.830.1326
r
we
o
nP
r
Tu
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
still attached.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Refer to warning w.1 on pg. 2
5
M3519-01 • 05/14/14 • © Hunter Fan Company
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
www.HunterFan.com
Option 1
Downrod
1.888.830.1326
skip to next page
Standard
Downrod
for ceilings 8-10’ high
Steps 1-5 to remove standard downrod pipe
1
2
4
Sold Separately
Slide
3
10
9
8
Steps 6-10 to reassemble with new pipe
6
M3519-01 • 05/14/14 • © Hunter Fan Company
5
Slide
Option 3
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Shorter
Downrod
for fans installed
close to ceiling
Sold Separately
Option 2
Included
(pre-assembled)
If you need a different downrod length follow these steps:
7
6
www.HunterFan.com
Downrod (continued)
1.888.830.1326
Using the provided Allen
wrench, loosen the setscrew on
the adapter to install the pipe
and ball assembly.
(not to scale)
8”
&
3/8”
STRIP
CUT
Note: The adapter cover is not
used for low-profile mounting.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Insert the downrod through the
adapter cover. Hand tighten the
downrod (at least 4-5 full turns)
until it stops.
8”
Use the Allen wrench to
securely retighten the setscrew.
3/8”
If the setscrew is not tightened
securely, the fan may fall.
7
M3519-01 • 05/14/14 • © Hunter Fan Company
Downrod (continued)
Install the adapter cover screws
and tighten them securely.
www.HunterFan.com
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
Put the wires and downrod
through the canopy. Let the canopy
sit loosely on top of the fan.
8
M3519-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Wiring
Note: To connect the
wires, hold the bare
metal leads together and
place a wire connector
over them, then twist
clockwise until tight.
OM CEILING
FR
T
KE
AC
FRO
white
FR
M FA N
OM FAN
FR
OM
white
ING BR
white (grounded)
Using the orange wire
connectors from
the
hardware bag,
connect the black wire
(ungrounded) from
the ceiling to the black
wire from the receiver.
Connect the white
wire (grounded) from
the ceiling to both the
white wire from the
receiver and the white
wire from the fan.
black
CEIL
1.888.830.1326
OM CEILING
FR
black
(ungrounded)
M
blue
green/yellow
stripe
O
FR
Using an orange wire
connector from
the
hardware
bag, connect the
3 grounding wires
(green, green/yellow
stripe, or bare copper)
coming from the
ceiling, downrod, and
hanging bracket.
blue
green/yellow stripe
RECEIV
ER
black
Using the orange
wire connectors
from the remote
control hardware
bag, connect the blue
wire from the receiver
to the blue wire (or
possibly black with
white stripe wire) from
the fan. Connect the
yellow wire from the
receiver to the black
wire from the fan.
OM
FR
yellow
green/yellow
stripe (grounding)
OM FAN
FR
www.HunterFan.com
RECEIV
ER
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
9
M3519-01 • 05/14/14 • © Hunter Fan Company
Canopy
www.HunterFan.com
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the
hardware bag.
Note: Fan style may vary.
10
M3519-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Blades
www.HunterFan.com
1.888.830.1326
Attach each blade to a blade iron using four
blade washers, found in the
hardware
bag, and four blade assembly screws, found
in the
hardware bag.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
11
M3519-01 • 05/14/14 • © Hunter Fan Company
Switch Housing
Screw two housing assembly screws
from the
hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
www.HunterFan.com
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
12
M3519-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Insert the third screw, found in
the
hardware bag, into place and
then tighten all three screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing fixture falling.
Light Kit
www.HunterFan.com
1.888.830.1326
Switch
Housing
Screw
Connect the plugs from the upper and
lower switch housings. Make sure to line
up the colored markings on
the connectors.
Partially install two of the switch housing
screws found in the
bag. Align the
keyhole slots in the light kit housing
with the housing assembly screws. Make
sure all the wires from the fan and the light
kit are snug inside the center of the light
kit, not pinched in between the upper
switch housing and the light kit or hanging
out of the sides.
13
M3519-01 • 05/14/14 • © Hunter Fan Company
Turn the light kit clockwise until the
housing assembly screws are firmly
situated in the narrow end of the keyhole
slots. Install the remaining screw into the
housing. Tighten all three screws securely.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light fixture falling.
Light Kit (continued)
www.HunterFan.com
1.888.830.1326
Tab
Notch
Bulb
Install the 18-Watt dimmable CFL
bulb into the socket. When necessary,
replace with bulbs of same wattage.
CONGRA
YOU’RETULATIONS!
DONE!
Align the notches in the glass bowl with the
tabs in the light kit. Attach the glass bowl to
the light kit by twisting it clockwise until it
snaps into place.
14
M3519-01 • 05/14/14 • © Hunter Fan Company
See next page for fan
operation instructions.
Operation, Maintenance, & Cleaning
www.HunterFan.com
Fan
Off
1.888.830.1326
Medium
Speed
High
Speed
Switch Cover
Plate
Battery
Door
Low
Speed
Light
Fan Off
High
Phillips
Head
Screw
Removed
Tabs
To access the battery compartment,
remove the small Phillips head screw
that secures the battery door to the
transmitter assembly. The battery
should be installed with the positive
(+) side up. Replace with a CR2032
battery when necessary.
Turn Power
ON
Note: The remote must be paired
before the fan will operate.
Within 3 minutes of restoring power
to the fan, press both the Fan Off
button and the High button for at
least 4 seconds. Your fan will turn on
low to indicate successful syncing.
If it does not, turn off power to your
fan, wait 1 minute then try again. If
using the transmitter with multiple
fans, repeat this process for each fan.
To turn on fan, press a fan speed
button. Speeds range from off (0)
to high (3). Quickly press the Light
button to turn the lights off and on.
15
M3519-01 • 05/14/14 • © Hunter Fan Company
Rocker- Style
Plate
To install the transmitter cradle, remove
the two screws holding the switch
cover plate. Do not remove the cover
plate. Orient the cradle by lining up
the two mounting holes with those on
the cover plate. Insert and tighten the
screws. Do not over tighten.
Note: For rocker-style cover plates,
break off the tabs by pushing outward.
Operation, Maintenance, & Cleaning (continued)
www.HunterFan.com
1.888.830.1326
Safe-Exit
The Safe-Exit Program gives
you about thirty seconds of light
when you turn the lights off to
exit the room before the lights go
out. To use Safe-Exit:
• Press the Fan Off button for at
least three seconds to initiate the
Safe-Exit Mode.
• The lights will flash for visual
confirmation.
• The lights will stay on 50%
brightness for 15 seconds and
then begin to dim. After a total
of 30 seconds, the lights will be
completely off.
Note: For CFL lighting, the lights
will stay on 100% brightness for 30
seconds. After a total of 30 seconds,
the lights will be completely off.
Reverse
Switch
To switch the direction of air flow, move
the reverse switch to the opposite
position. You will need to remove the
light kit glass to do so.
16
M3519-01 • 05/14/14 • © Hunter Fan Company
For cleaning the fan, use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the finishes.
Troubleshooting
Fan doesn’t work
• Make sure power switch is on.
• Pull the pull chain to make sure it
is on.
• Push the motor reversing switch
firmly left or right to ensure that it
is engaged.
www.HunterFan.com
CFL bulbs flicker or do not dim
• Turn the power switch off and
back on. Within three minutes,
hold down the Fan Off button
while pressing the Light
button twice. If the problem
is not corrected, repeat the
process up to three times.
Remote control of fan is erratic
Excessive wobbling
• Make sure the battery is
installed correctly.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Install a fresh battery.
Transmitter only works when
held at close range
• Install a fresh battery.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 9.
• Make sure the battery is working.
• Check the plug connection in the
switch housing.
Noisy operation
If you have multiple remotes or
multiple remote-controlled fans
installed on the same circuit
breaker and you are experiencing
interference or faulty operation of
your remote controls, please go to
www.HunterFan.com/FAQs
and click “How do I properly install
multiple remote-controlled fans?”
for information on how to correct
this issue.
• Tighten the blade and blade iron
screws until they are snug.
• Check to see if any of the blades
are cracked. If so, replace all of
the blades.
1.888.830.1326
17
M3519-01 • 05/14/14 • © Hunter Fan Company
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Use the provided balancing
kit and instructions to balance
the fan.