Hunter 59046 Use and Care Manual

www.HunterFan.com
Table of Contents
What to Expect with
Your Installation
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
Tools Needed
Mounting Options
1.888.830.1326
Ceiling Bracket
30 inches
12
PA G E
Troubleshooting
?
?
?
19
PA G E
18
PA G E
1
M3542-01 • 11/05/13 • © Hunter Fan Company
PA G E
15
PA G E
PA G E
14
PA G E
Maintenance
& Cleaning
Light Kit
5
Wiring
9
PA G E
Blades
13
Downrod
7
PA G E
Canopy
4
PA G E
Blade Irons
6
Save your receipt for proof of purchase.
3
PA G E
Preparation
To register your fan, please visit:
www.HunterFan.com/register
Ladder
PA G E
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
2
PA G E
7 feet
www.HunterFan.com
What to Expect with Your Installation
Read and Save These Instructions
If you are unfamiliar
with wiring, use a
qualified electrician.
This product conforms to UL Standard 507.
WARNINGS
30 inches
from blade tip
to nearest wall
or obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Check box to see
fan weight
7 feet
from bottom
edge of blade
to the floor
You may need a
friend to help you.
Assess location
w.1 - To reduce the risk of fire, electrical shock, or
personal injury, mount fan directly from building
structure and/or an outlet box marked acceptable for
fan support of 70 lbs (31.8 kg) and use the mounting
screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing
or servicing your fan, disconnect the power by turning
off the circuit breakers to the outlet box and associated
wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent
warning device, such as a tag, to the service panel.
1
Standard Downrod
w.3 - To reduce the risk of fire, electrical shock, or motor
damage, use only Hunter Solid State Speed Controls.
2
Shorter Downrod
w.4 - To reduce the risk of personal injury, do not bend the
blade brackets when installing the blade brackets, balancing
the blades, or cleaning the fan. Do not insert foreign objects
in between rotating fan blades.
3
for ceilings 8-10 feet high
for fans installed close to ceiling
Longer Downrod
for ceilings 10 feet or higher
CAUTIONS
c.1 - All wiring must be in accordance with national and
local electrical codes ANSI/NFPA 70. If you are unfamiliar
with wiring, use a qualified electrician.
c.2 - Use only Hunter replacement parts.
Assess ceiling angle
1.888.830.1326
Select a downrod length
2
M3542-01 • 11/05/13 • © Hunter Fan Company
www.HunterFan.com
Tools Needed
Ladder
Pliers
Wire Strippers
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
M3542-01 • 11/05/13 • © Hunter Fan Company
Screwdrivers
1.888.830.1326
34O
CEILING
www.HunterFan.com
Mounting Options
OPTION 1
If you have a flat ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by a standard downrod (included).
1.888.830.1326
1.866.268.1936
Use Standard Mounting
or Low-Profile Mounting
to hang the fan from a flat ceiling.
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
4
M3542-01 • 11/05/13 • © Hunter Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
Ceiling Bracket
www.HunterFan.com
1.888.830.1326
For angled ceilings, point
opening toward peak.
r
we
o
nP
r
Tu
F
OF
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four (4) bumpers
are still attached.
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Refer to warning w.1 on pg. 2
5
M3542-01 • 11/05/13 • © Hunter Fan Company
Ceiling Bracket (continued)
Preparation
www.HunterFan.com
1.888.830.1326
!
KEEP
DISC
D
AR
Time Saver Tip: Get a helper
to insert grommets, found in
the
hardware bag, into the
blades while you’re doing the
next couple of steps.
Remove the shipping blocks from the
motor. Save the screws. They will be
needed for blade ring installation.
Note: Some fans will have a shipping
ring instead of shipping blocks. Please
remove the ring and save the screws.
6
M3542-01 • 11/05/13 • © Hunter Fan Company
Blade Irons
Turn the fan motor upside-down and place
it in one of the holes in the packaging.
www.HunterFan.com
Insert each blade iron into a slot in the
blade ring as shown.
7
M3542-01 • 11/05/13 • © Hunter Fan Company
1.888.830.1326
Attach each blade iron to the blade ring
using three blade iron screws, found in
the
hardware bag.
Blade Irons (continued)
www.HunterFan.com
Remember the screws you
kept after removing the
shipping blocks (page 6)? You
need them for this step.
Attach the blade ring to the bottom of the
fan using the five blade ring screws.
8
M3542-01 • 11/05/13 • © Hunter Fan Company
1.888.830.1326
www.HunterFan.com
Option 1
Downrod
1.888.830.1326
skip to next page
Standard
Downrod
for ceilings 8-10’ high
Steps 1-5 to remove standard downrod pipe
1
2
4
Sold Separately
Slide
3
10
9
8
Steps 6-10 to reassemble with new pipe
9
M3542-01 • 11/05/13 • © Hunter Fan Company
5
Slide
Option 3
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Shorter
Downrod
for fans installed
close to ceiling
Included
Option 2
Included
(pre-assembled)
If you need a different downrod length follow these steps:
7
6
www.HunterFan.com
KEEP!
(not to scale)
8”
&
3/8”
1.888.830.1326
STRIP
CUT
Downrod (continued)
!
KEEP
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the
downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
3/8”
If the setscrew is not tightened
securely, the fan may fall.
10
M3542-01 • 11/05/13 • © Hunter Fan Company
www.HunterFan.com
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
11
M3542-01 • 11/05/13 • © Hunter Fan Company
1.888.830.1326
Wiring
OM
FR
CEILIN
www.HunterFan.com
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
G
OM
FR
T
KE
Black
FR
(Ungrounded)
M FA N
Blue
FRO
(Ungrounded)
AC
Blue
ING BR
Black
CEIL
White
M
Using the orange wire
connectors from
the
hardware bag, connect
the black wire (ungrounded)
from the ceiling to the black
and the blue wires from the
fan. Connect the white wire
(grounded) from the ceiling to
the white wire from the fan.
Using the orange wire
connectors from
the
hardware bag,
connect the white wire
(grounded) from the
ceiling to the white wire
from the fan.
Connect the black wire
(ungrounded) from the
ceiling to the black wire
from the fan. Connect the
second (ungrounded) wire
from the ceiling to the blue
wire from the fan.
White
Green/Yellow
Stripe
FR
O
For a Single Switch
For Dual Switches
(Grounded)
Green/Yellow
Stripe
Using an orange wire
connector from
the
hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, downrod, and
hanging bracket.
CEILIN
OM
G
FR
G
(Ungrounded)
(Grounded)
(Grounding)
OM FAN
FR
CEILIN
1.888.830.1326
O M FA N
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
12
M3542-01 • 11/05/13 • © Hunter Fan Company
www.HunterFan.com
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the
hardware bag.
13
M3542-01 • 11/05/13 • © Hunter Fan Company
1.888.830.1326
Blades
www.HunterFan.com
Insert grommets, found in the
hardware
bag, into the holes in the blades.
1.888.830.1326
Secure each blade to a blade iron with three
blade screws, found in the
hardware bag.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
14
M3542-01 • 11/05/13 • © Hunter Fan Company
Light Kit
www.HunterFan.com
Screw two housing assembly screws from
the
hardware bag halfway into the
motor housing. It does not matter which
two screw holes you choose.
Feed the wire plug through the center
hole of the light kit mounting plate, then
wrap keyhole slots around the screws and
twist counterclockwise.
the
1.888.830.1326
Insert the third screw, found in
hardware bag, into place and then
tighten all three screws.
Make sure the mounting plate is securely attached
to the motor housing. Failure to properly secure all
3 assembly screws could result in the light kit fixture
falling.
Note: Fan style may vary.
15
M3542-01 • 11/05/13 • © Hunter Fan Company
www.HunterFan.com
Light Kit (continued)
1.888.830.1326
Switch
Housing
Screws
Partially install two of the switch housing
screws, found in the
bag, into the light
kit mounting plate.
Connect the upper plug connector from the
fan to the lower plug connector in the light
kit. Make sure to line up the colored markings
on the connectors. Align the keyhole slots in
the light kit with the partially installed screws
in the mounting plate. Turn the light kit
clockwise until the screws are nestled into the
small ends of the keyhole slots.
16
M3542-01 • 11/05/13 • © Hunter Fan Company
Install the third switch housing screw.
Tighten all three screws securely.
Make sure the light kit is securely attached to the mounting
plate. Failure to properly secure all three assembly screws
could result in the light fixture falling.
www.HunterFan.com
Light Kit (continued)
1.888.830.1326
Metal
Plate
Globe
Finial
Cap
CONGRA
T
YOU’REULATIONS!
DONE!
Finial
Install a bulb into each of
the sockets. When necessary,
replace with bulbs of the same
type and wattage.
Thread the pull chains through the
holes in the metal plate, globe, and
finial cap. Place the finial cap flush
against the globe and align the holes.
Light the globe and finial cap to the
threaded rod in the light kit, then
screw the finial onto the thread rod
until it is secure.
Connect the appropriate pull
chain pendant to each of the short
chains coming from the finial cap.
The fan pull chain controls the
speed: from high to off. The light
pull chain controls the light fixture:
on and off.
17
M3542-01 • 11/05/13 • © Hunter Fan Company
See next page for fan
operation instructions.
Note: In compliance with US federal energy regulations, this ceiling fan
contains a device that restricts its light output. Exceeding the wattage
limit marked on the MAX wattage sticker affixed to the light socket(s)
may result in fire hazard or improper operation.
Maintenance & Cleaning
er
w
o
nP
r
Tu
ON
www.HunterFan.com
1.888.830.1326
Metal
Plate
Globe
Finial
Cap
Reverse
Switch
Finial
Changing the bulbs - unscrew
the finial and remove it from the
threaded rod. Remove the finial cap
while supporting the globe with your
other hand. Carefully remove the
globe. Unscrew bulbs and replace
with bulbs of same type and wattage.
Reinstall the globe assembly.
Changing the direction of
air flow - Carefully remove the
globe assembly, then move the
reverse switch to the opposite
position.
18
M3542-01 • 11/05/13 • © Hunter Fan Company
Cleaning the fan - use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the finishes.
www.HunterFan.com
Troubleshooting
Fan doesn’t work
Excessive wobbling
Noisy Operation
• Make sure power switch is on.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Tighten the blade and blade
iron screws until they are snug.
• Pull the pull chain to make sure
it is on.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Use the provided balancing
kit and instructions to balance
the fan.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 12.
• Check the plug connection in
the switch housing.
19
M3542-01 • 11/05/13 • © Hunter Fan Company
1.888.830.1326
Lights dim when turned on or do not turn on at all.
• Make sure the wattage of the
light bulbs installed matches
the specifications on the light
sockets.
Download PDF
Similar pages
Hunter 53086 fan
Hunter 53249 Use and Care Manual
Hunter 53249 Instructions / Assembly
Hunter 52019 Installation Guide
Hunter 52" Astoria
Hunter 52" Sonic