Hunter 53033 Use and Care Manual

www.HunterFan.com
Table of Contents
What to Expect with
Your Installation
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
Ceiling Bracket
10
PA G E
11
Troubleshooting
?
?
?
19
PA G E
17
PA G E
1
M0019-01 • 04/19/13 • © Hunter Fan Company
16
5
Canopy
Operation,
Maintenance & Cleaning
PA G E
14
PA G E
Remote Control
PA G E
PA G E
PA G E
13
Light Kit
Wiring
7
PA G E
Switch Housing
4
PA G E
Downrod
6
Save your receipt for proof of purchase.
3
PA G E
Preparation
Ladder
PA G E
PA G E
2
PA G E
7 feet
To register your fan, please visit:
www.HunterFan.com/register
12
Mounting Options
30 inches
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
Blades
Tools Needed
1.888.830.1326
www.HunterFan.com
What to Expect with Your Installation
Read and Save These Instructions
If you are unfamiliar
with wiring, use a
qualified electrician.
This product conforms to UL Standard 507.
WARNINGS
30 inches
from blade tip
to nearest wall
or obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Check box to see
fan weight
7 feet
from bottom
edge of blade
to the floor
You may need a
friend to help you.
Assess location
w.1 - To reduce the risk of fire, electrical shock, or
personal injury, mount fan directly from building
structure and/or an outlet box marked acceptable for
fan support of 70 lbs (31.8 kg) and use the mounting
screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing
or servicing your fan, disconnect the power by turning
off the circuit breakers to the outlet box and associated
wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent
warning device, such as a tag, to the service panel.
1
Standard Downrod
w.3 - To reduce the risk of fire, electrical shock, or motor
damage, use only Hunter Solid State Speed Controls.
2
Shorter Downrod
w.4 - To reduce the risk of personal injury, do not bend the
blade brackets when installing the blade brackets, balancing
the blades, or cleaning the fan. Do not insert foreign objects
in between rotating fan blades.
3
for ceilings 8-10 feet high
for fans installed close to ceiling
Longer Downrod
for ceilings 10 feet or higher
CAUTIONS
c.1 - All wiring must be in accordance with national and
local electrical codes ANSI/NFPA 70. If you are unfamiliar
with wiring, use a qualified electrician.
c.2 - Use only Hunter replacement parts.
Assess ceiling angle
1.888.830.1326
Select a downrod length
2
M0019-01 • 04/19/13 • © Hunter Fan Company
www.HunterFan.com
Tools Needed
Ladder
Pliers
Wire Strippers
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
M0019-01 • 04/19/13 • © Hunter Fan Company
Screwdrivers
1.888.830.1326
34O
CEILING
www.HunterFan.com
Mounting Options
OPTION 1
If you have a flat ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by a standard downrod (included).
1.888.830.1326
1.866.268.1936
Use Standard Mounting
or Low-Profile Mounting
to hang the fan from a flat ceiling.
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
4
M0019-01 • 04/19/13 • © Hunter Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
Ceiling Bracket
www.HunterFan.com
1.888.830.1326
For angled ceilings, point
opening toward peak.
er
w
o
nP
r
Tu
OFF
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four (4) bumpers
are still attached.
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Refer to warning w.1 on pg. 2
5
M0019-01 • 04/19/13 • © Hunter Fan Company
Ceiling Bracket (continued)
Preparation
www.HunterFan.com
1.888.830.1326
!
KEEP
DISC
D
AR
Time Saver Tip: Get a helper
to insert grommets, found in
the
hardware bag, into the
blades while you’re doing the
next couple of steps.
Remove the shipping blocks from the
motor. Save the screws. They will be
needed for blade iron installation.
Note: Some fans will have a shipping
ring instead of shipping blocks. Please
remove the ring and save the screws.
6
M0019-01 • 04/19/13 • © Hunter Fan Company
www.HunterFan.com
Option 1
Downrod
1.888.830.1326
skip to next page
Standard
Downrod
for ceilings 8-10’ high
Steps 1-5 to remove standard downrod pipe
1
2
4
Sold Separately
Slide
3
10
9
8
Steps 6-10 to reassemble with new pipe
7
M0019-01 • 04/19/13 • © Hunter Fan Company
5
Slide
Option 3
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Shorter
Downrod
for fans installed
close to ceiling
Included
Option 2
Included
(pre-assembled)
If you need a different downrod length follow these steps:
7
6
www.HunterFan.com
KEEP!
(not to scale)
8”
&
3/8”
1.888.830.1326
STRIP
CUT
Downrod (continued)
!
KEEP
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
3/8”
If the setscrew is not tightened
securely, the fan may fall.
8
M0019-01 • 04/19/13 • © Hunter Fan Company
www.HunterFan.com
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
9
M0019-01 • 04/19/13 • © Hunter Fan Company
1.888.830.1326
Wiring
www.HunterFan.com
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
CEILIN
G
OM
FR
T
KE
black (live in)
FR
black (ungrounded)
M FA N
white (neutral in)
FRO
Using an orange wire
connector from
the
hardware bag,
connect the black wire
(ungrounded) from the
ceiling to the black wire
from the receiver (marked
“live in”). Connect the
white wire (grounded)
from the ceiling to
the white wire from
the receiver (marked
“neutral in”).
white (grounded)
C
blue
A
ING BR
CEILIN
G
OM
FR
blue (light out)
CEIL
black
M
white
green/yellow stripe
O
FR
Using an orange wire
connector from
the
hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, downrod, and
hanging bracket.
RECEIVE
R
black (fan out)
green/yellow stripe
Using the blue wire
connectors from the remote
control hardware bag,
connect the white wire
from the receiver (marked
“common out”) to the white
wire from fan. Connect the
black wire from the receiver
(marked “fan out”) to the
black wire from the fan.
Connect the blue wire from
the receiver (marked ”light
out”) to the blue wire from
the fan. The red wire from
the receiver will not be used,
it has a pre-installed wire
terminator.
white (common out)
green/yellow stripe
(grounding)
OM FAN
FR
OM
FR
1.888.830.1326
OM
RECEIV
ER
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
10
M0019-01 • 04/19/13 • © Hunter Fan Company
www.HunterFan.com
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the
hardware bag.
Note: Fan style may vary.
11
M0019-01 • 04/19/13 • © Hunter Fan Company
1.888.830.1326
Blades
www.HunterFan.com
1.888.830.1326
Remember the screws that
you kept after removing the
shipping blocks (page 6)? You
need them for this step.
Insert grommets found in the
hardware
bag into the holes in the blades, then
secure each blade to a blade iron with
screws found in the
hardware bag.
Lightly attach the blade irons to the
motor with the blade iron armature
screws, then securely tighten after both
screws are attached.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
12
M0019-01 • 04/19/13 • © Hunter Fan Company
Switch Housing
Screw two (2) housing assembly screws
from the
hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
www.HunterFan.com
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
the
1.888.830.1326
Insert the third screw, found in
hardware bag, into place and then
tighten all three (3) screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing fixture falling.
13
M0019-01 • 04/19/13 • © Hunter Fan Company
www.HunterFan.com
Light Kit
Switch
Housing
Screw
Partially install two of the switch housing
screws found in the
bag. Connect
the plugs from the upper and lower
switch housings. Make sure to line up the
colored markings on the connectors.
Want to install your fan without a light kit?
Go to www.HunterFan.com/FAQs and click
“How do I install my fan without the light kit?”
Switch
Housing
Screw
1.888.830.1326
Notch
Align the notches in the sides of the lower
switch housing with the upper switch
housing screws. Lift the lower switch
housing. Twist the lower switch housing
clockwise to lock into place.
14
M0019-01 • 04/19/13 • © Hunter Fan Company
Install the third switch housing screw.
Tighten all three screws securely.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light fixture falling.
www.HunterFan.com
Light Kit (continued)
1.888.830.1326
Metal
Plate
Globe
Globe
Keeper
Finial
Cap
Finial
Install a light bulb in each socket.
Note: Do not use CFL bulbs to
replace your light bulbs. Your
lights may flicker or fail to work.
Note: Globe style and number of
lights may vary.
Press the globe and globe keeper
flush against the metal plate.
Place the finial cap up against the
globe and screw the finial onto the
threaded rod end until tight.
15
M0019-01 • 04/19/13 • © Hunter Fan Company
CONGRA
YOU’RETULATIONS!
DONE!
See next page for fan
operation instructions.
Note: In compliance with US federal energy regulations, this ceiling fan
contains a device that restricts its light output. Exceeding the wattage
limit marked on the MAX wattage sticker affixed to the light socket(s)
may result in fire hazard or improper operation.
www.HunterFan.com
Remote Control
r
Tu
r
we
o
nP
ON
Battery
Door
1.888.830.1326
Fan Off
High
Phillips
Head
Screw
To access the battery compartment, remove
the small Phillips head screw that secures the
battery door to the transmitter assembly. The
battery should be installed with the positive
(+) side up. Replace with a CR2032 battery
when necessary.
16
M0019-01 • 04/19/13 • © Hunter Fan Company
Note: The remote must be paired before
the fan will operate.
Within 3 minutes of restoring power to
the fan, press both the Fan Off button and
the High button for at least 4 seconds. Your
fan will turn on low to indicate successful
syncing. If it does not, turn off power to your
fan, wait 1 minute then try again. If using the
transmitter with multiple fans, repeat this
process for each fan.
Operation, Maintenance, & Cleaning
www.HunterFan.com
1.888.830.1326
Medium
Speed
Fan
Off
High
Speed
Switch Cover Plate
Low
Speed
Light
Reverse
Switch
Removed
Tabs
To turn on fan, press a fan speed button. Speeds
range from off (0) to high (3). Quickly press the
Light button to turn the lights off and on.
Rocker- Style
Plate
To install the transmitter cradle, remove the
two screws holding the switch cover plate. Do
not remove the cover plate. Orient the cradle
by lining up the two mounting holes with
those on the cover plate. Insert and tighten
the screws. Do not over tighten.
Note: For rocker-style cover plates, break off
the tabs by pushing outward.
17
M0019-01 • 04/19/13 • © Hunter Fan Company
To switch the direction of air flow, move the
reverse switch to the opposite position.
Operation, Maintenance, & Cleaning (continued)
www.HunterFan.com
1.888.830.1326
Safe-Exit
The Safe-Exit Program gives you about thirty
seconds of light when you turn the lights off
to exit the room before the lights go out. To
use Safe-Exit:
Metal
Plate
• Press the Fan Off button for at least three
seconds to initiate the Safe-Exit Mode.
• The lights will flash for visual
confirmation.
Globe
• The lights will stay on 50% brightness for
15 seconds and then begin to dim. After
a total of 30 seconds, the lights will be
completely off.
Globe
Keeper
Finial
Cap
Finial
Changing the bulbs - unscrew
the finial and remove it from the
threaded rod. Remove the finial cap
and unscrew the globe keeper while
supporting the globe with your other
hand. Carefully remove the globe.
Unscrew bulbs and replace with
bulbs of same type and wattage.
Reinstall the globe assembly.
When cleaning the fan, use soft brushes
or cloths to prevent scratching. Cleaning
products may damage the finishes.
18
M0019-01 • 04/19/13 • © Hunter Fan Company
For questions regarding removing a light kit, call
customer service 1-888-830-1326.
www.HunterFan.com
Troubleshooting
Fan doesn’t work
Excessive wobbling
Noisy operation
• Make sure power switch is on.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Tighten the blade and blade
iron screws until they are snug.
• Pull the pull chain to make sure
it is on.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Use the provided balancing
kit and instructions to balance
the fan.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 10.
Remote control of fan is erratic
• Check the plug connection in
the switch housing.
• Install a fresh battery.
• Make sure the battery is
installed correctly.
Transmitter only works when
held at close range
• Change battery.
19
M0019-01 • 04/19/13 • © Hunter Fan Company
1.888.830.1326
Lights dim when turned on or do not turn on at all.
• Make sure the wattage of the
light bulbs installed matches
the specifications on the light
sockets.
Download PDF
Similar pages
Hunter 52" Sonic
Hunter 59072 Use and Care Manual
Hunter 53249 Use and Care Manual
Hunter 53086 fan
Hunter 99121 fan
Hunter 52" Astoria
Hunter 53249 Instructions / Assembly